Revision History

item

item

none

3.14

03/2025

NEW Content

• Working with Automation Rules

• TTC - Tighten to Clutch

• CRh - Clutch Rehit

• Machine Capability Test Mode Active - 10148: Added an Input/Output signal

• Toggles Machine Capability Mode - 10152: Added an Input signal

UPDATED Content

• Event Codes

• General Virtual Station: Added information on Maximum consecutive loosenings

• Open End in Open Position - 89: Output signal enabled for Fieldbus

• General Virtual Station

• Connecting to web GUI via service Ethernet port

• Multistep Programs

• Adding a Multistep Program

• Deleting a Multistep Program

• Validate a Tool with a Tightening Program

• Settings for a Multistep Program

• Updating Controller Software through USB

• Updating Controller Software through Web GUI

• Web GUI

• Configuration of the Extended Logging

3.13

09/2024

NEW content

• Source Tightening Properties

• Unpair Bluetooth Connection

• Configuration of HTTPS

• Configuring HTTPS

• Certificates

UPDATED content

• Configuring a Source Tightening

• Supported Tools

• Calibrating the Tool

• Configuring the Factory Ethernet Port

• Configuring the Firewall

• Configuring the ToolsNet Connection

• Configuring the ToolsTalk Connection

• EM Stop Connection Scenarios

• Live Results

• Event Codes

• Step Monitors

3.11

02/2024

• UPDATED content

• Multistep GUI

• Event Codes updated.

• NOK Results List updated.

• "StepSync" replaced with "controller" or "synchronized tightening" in the user guide.

• Configuration of the Tool LEDs updated.

3.10

06/2023

• NEW content

• Configuring the Controller as a Wireless Access Point added to Configuration of the Network.

• Troubleshooting Matrix added to Troubleshooting and Service

• UPDATED content

• Tool Diagnostics Diagnostic test added to Tool Diagnostics.

• PrT - Prevailing Torque added in Configuration for FlexSystem and StepSync.

• Exporting Logs from Connected Tools QST-M added.

• Event Codes updated with battery status.

• Configuring Protocols Window in a Virtual Station updated with communication timeout value.

3.9

01/2023

• NEW content

• Configuration > Working with the Too Tab > Tool Diagnostics

• Configuration > Working with the Tool Tab > Zero Position

• Configuration > Working with the Settings Tab > Configuration of IxB Connect

• Configuration > Working with the Configurations Tab >Tool Configuration > Configuration of the Dual Transducers

• UPDATED content

• Configuration > Working with the Controller Tab > Exporting Systems Logs and Information

• Configuration > Working with the Controller Tab > Export/Import > Exporting logs from Connected Tools

• Configuration > Working with the Tightening Tab > Multistep Programs > Tightening Steps

• Configuration > Working with the Tightening Tab > Multistep Programs > Step Monitors

• Configuration > Working with the Configurations Tab > General Virtual Station

• Configuration > Working with the Settings Tab > Configuration of the Network > Configuring the Firewall

3.8

06/2022

NEW content:

• Configuration > Working with the Controller Tab > Export/Import > Exporting "System logs and information"

UPDATED content:

• Configuration > Working with the Controller Tab > StepSync

• Configuration > Working with the Controller Tab > StepSync > StepSync Tightenings

• Configuration > Working with the Controller Tab > StepSync > StepSync Signals

• Configuration > Working with the Tightening Tab > Multistep Programs (new filterable tables for tightening steps, step monitors and step restrictions).

• Configuration > Working with the Tightening Tab > Multistep Programs (Creating Multistep Program inserted into Adding a Multistep Program)

3.7

01/2022

NEW content:

• Configurations Tab > Tool Configuration > Configuration of the Open End

• Settings Tab > Configuration of the Server Connections > Configuring the Remote Logging Connection

• Settings Tab > Configuration of the Extended Logging

• Settings Tab > Configuration of the Extended Logging > Configuring the Log Groups

UPDATED content:

• Multistep Programs > Tightening Steps (TC - Torque Calibration)

• Multistep Programs > Step Monitors (C - Current, TC - Torque Calibration)

• Multistep Programs > Settings for a Multistep Program (Program Monitor - Time, Program Restriction - Angle, Program Restriction - Time)

• Multistep Programs > Step Restrictions (C - Current)

• Event Codes list

• Input Signals - Power Focus 8

• Input Signals - StepSync

• Output Signals - Power Focus 8

• Output Signals - StepSync

3.6

06/2021

First official release of the user guide for POWER FOCUS 8.