1. ToolsTalk 2 FLEX
2. References
3. Fieldbus Signals
4. Output Signals

Output Signals

• Active Identifier String - 186
• Active Identifier String 1 - 188
• Active Identifier String 2 - 189
• Active Identifier String 3 - 190
• Active Identifier String 4 - 191
• Batch Completed - 30
• Batch Completed NOK - 37
• Batch Completed OK - 36
• Batch Count - 31
• Batch Running - 32
• Batch Sequence Completed NOK - 46
• Batch Sequence Completed OK - 45
• Batch Sequence Done - 48
• Batch Sequence Running - 47
• Bolt Tightening Status - 79
  • Subsignals
    • All signals
    • Cycle running
    • Inhibited
    • In Selected Mode
    • Running repair
    • Running termination
    • Tightening running
    • Loosening running
    • Last cycle OK
    • Last cycle NOK
    • Last cycle Inhibited
    • Last cycle Not included
    • Last cycle Terminated by other
    • Last cycle Hardware error
    • Tool Led Mirror Green
    • Tool Led Mirror Yellow
    • Tool Led Mirror Red
    • Last tightening OK
    • Last tightening NOK
    • Last loosening OK
    • Last loosening NOK
    • Last cycle Timeout
    • Last cycle Torque High
    • Last cycle Torque Low
    • Last cycle Angle High
    • Last cycle Angle Low
• Channel Hardware Status - 81
  • Subsignals
    • All signals
    • General HW error
    • Tool temp high
    • Drive temp high
    • Motortune needed
    • Drive voltage error
    • Emergency stop active
    • Tool cable invalid
    • Tool disconnected
    • Drive disconnected
    • Torque transducer error
• Channel Tightening Status - 80
  • Subsignals
    • All signals
    • Cycle running
    • Inhibited
    • In Selected Mode
    • Running repair
    • Running termination
    • Tightening running
    • Loosening running
    • Last cycle OK
    • Last cycle NOK
    • Last cycle Inhibited
    • Last cycle Not included
    • Last cycle Terminated by other
    • Last cycle Hardware error
    • Tool Led Mirror Green
    • Tool Led Mirror Yellow
    • Tool Led Mirror Red
    • Last tightening OK
    • Last tightening NOK
    • Last loosening OK
    • Last loosening NOK
    • Last cycle Timeout
    • Last cycle Torque High
    • Last cycle Torque Low
    • Last cycle Angle High
    • Last cycle Angle Low
• Configuration Version - 88
• Controller Switched On - 42
• Current Running Batch - 180
• Cycle Complete - 77
• Cycle NOK - 76
• Cycle OK - 75
• Cycle Running - 78
• Cycle Ready To Start - 82
• Emergency Stop - 20036
• Event Code - 30001
• Event Code Severity - 30003
• Event Present - 161
• Fieldbus AsyncData From PF - 107
• Fieldbus Disconnected - 96
• From SoftPLC - 10064
• Last Received Identifier String - 187
• Loosening is Locked - 28
• Loosening NOK - 74
• Loosening OK - 70
• Max Consecutive NOK Reached - 35
• No System Error - 83
• No System Warning - 102
• Program Start - 132
• Read Result Queue Flushed - 30006
• Received Identifier 1 - 192
• Received Identifier 2 - 193
• Received Identifier 3 - 194
• Received Identifier 4 - 195
• Remaining Batch - 33
• Selected Mode Id - 72
• Selected Sequence Bit 0 - 139
• Selected Sequence Bit 1 - 140
• Selected Sequence Bit 2 - 141
• Selected Sequence Bit 3 - 142
• Selected Sequence Bit 4 - 143
• Selected Sequence Bit 5 - 144
• Selected Sequence Bit 6 - 145
• Selected Sequence Bit 7 - 146
• Selected Sequence Bit 8 - 147
• Selected Sequence Bit 9 - 163
• Selected Sequence Id - 84
• Sequence Aborted - 160
• Service Indicator Alarm - 137
• Size of Sequence - 181
• Software Major Version - 86
• Software Minor Version - 87
• Software Release Version - 85
• Station Ready - 71
• Test Bolt Activated - 91
• Tightening is Locked - 27
• Tightening NOK - 4
• Tightening OK - 3
• Tool Loosening - 22
• Tool Tightening - 21