Error Codes
The below error codes are the same for the Handheld Tightening Module, Fixtured Tightening Module, and Vacuum Tightening Module.
No. | State | Unit | Error Message |
0 | General | No Fault | |
1 | System | Overcurrent_Isys | |
2 | System | Overvoltage_Field_Supply_V2 | |
3 | System | Undervoltage_Field_Supply_V2 | |
4 | System | Overvoltage_Field_Supply_V1 | |
5 | System | Undervoltage_Field_Supply_V1 | |
6 | System | Modulebus_Communication_Lost | |
7 | Modulebus_Configuration_Error | ||
8 | System | IO_Basic_Diagnostics_Overcurrent_output_1 (Internal IO-Hub) | |
9 | System | IO_Basic_Diagnostics_Overcurrent_output_3 (Valveblock) | |
10 | System | IO_Basic_Diagnostics_Overcurrent_output_5 (NA) | |
11 | System | IO_Basic_Diagnostics_Overcurrent_output_7 (IO-Hub fixture) | |
12 | System | IO_Diagnostics_Input_Wrong_or_missing_device_0 (Internal IO-Hub) | |
13 | System | IO_Diagnostics_Input_Wrong_or_missing_device_2 (Valveblock) | |
14 | System | IO_Diagnostics_Input_Wrong_or_missing_device_4 (NA) | |
15 | System | IO_Diagnostics_Input_Wrong_or_missing_device_6 (IO-Hub fixture) | |
16 | System | IO_Diagnostics_Input_Common_error_0 (Internal IO-Hub) | |
17 | System | IO_Diagnostics_Input_Common_error_2 (Valveblock) | |
18 | System | IO_Diagnostics_Input_Common_error_4 (NA) | |
19 | System | IO_Diagnostics_Input_Common_error_6 (IO-Hub fixture) | |
31 | System | Overcurrent_Isys | |
32 | System | Overvoltage_Field_Supply_V2 | |
33 | System | Undervoltage_Field_Supply_V2 | |
34 | System | Overvoltage_Field_Supply_V1 | |
35 | System | Undervoltage_Field_Supply_V1 | |
36 | System | Modulebus_Communication_Lost | |
37 | System | Modulebus_Configuration_Error | |
38 | System | IO_Basic_Diagnostics_Overcurrent_output_1 | |
39 | System | IO_Basic_Diagnostics_Overcurrent_output_3 | |
40 | System | IO_Basic_Diagnostics_Overcurrent_output_5 (vac sens) | |
41 | System | IO_Basic_Diagnostics_Overcurrent_output_7 (IO-Hub fixture) | |
42 | System | IO_Diagnostics_Input_Wrong_or_missing_device_0 | |
43 | System | IO_Diagnostics_Input_Wrong_or_missing_device_2 | |
44 | System | IO_Diagnostics_Input_Wrong_or_missing_device_4 (vac sens) | |
45 | System | IO_Diagnostics_Input_Wrong_or_missing_device_6 (IO-Hub fixture) | |
46 | System | IO_Diagnostics_Input_Common_error_0 | |
47 | System | IO_Diagnostics_Input_Common_error_2 | |
48 | System | IO_Diagnostics_Input_Common_error_4 (vac sens) | |
49 | System | IO_Diagnostics_Input_Common_error_6 (IO-Hub fixture) | |
100 | Startup | Feeder | System (re)booted |
101 | Startup | ConBox | System (re)booted |
200 | STPR_ErrorUp | Stepper | Stepper did not reach working position |
201 | STPR_ErrorDown | Stepper | Stepper did not leave working position |
202 | STPR_ErrorCounter | Stepper | No screw detected, feeder empty? |
300 | STF_SinglingErrorOpen | Separation | Singling stroke did not reach working position |
301 | STF_Error_WaitScrew | Separation | No Screw after separation detected, feeder empty? |
302 | STF_SinglingErrorClose | Separation | Singling stroke did not reach home position |
303 | STF_Error_BlowScrew | Separation | No Screw detected at tool sensor |
303 | STV_Error_Blow_Screw | Separation VTM | Screw did not arrive at tool |
304 | STF_SensorError | Screw to tool | Screw sensor separation error |
305 | Screw sensor tool fault | ||
401 | STV_ErrorRetractBitForPickup | Screw to vacuum | Bit stroke not in home position |
403 | STV_ErrorMoveBitToPickup | Screw to vacuum | Picking: Bit stroke did not leave home position |
404 | STV_ErrorRemoveScrewFromPickup | Screw to vacuum | Picking: Bit stroke did not reach home position |
405 | STV_ErrorVacuum | Screw to vacuum | Picking: required vacuum level not reached |
406 | STV_ErrorMovePusherToHP | Screw to vacuum | Slider: Home position not reached |
407 | Screw to vacuum | Vacuum lost |
