EBB26-055-P-U
Battery drill
Product Information
General Information
WARNINGRisk of Property Damage or Severe Injury
Ensure that you read, understand and follow all instructions before operating the tool. Failure to follow all the instructions may result in electric shock, fire, property damage and/or severe bodily injury.
Read all Safety Information delivered together with the different parts of the system.
Read all Product Instructions for installation, operation and maintenance of the different parts of the system.
Read all locally legislated safety regulations regarding the system and parts thereof.
Save all Safety Information and instructions for future reference.
Safety Signal Words
The safety signal words Danger, Warning, Caution, and Notice have the following meanings:
DANGER | DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. |
WARNING | WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. |
CAUTION | CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. |
NOTICE | NOTICE is used to address practices not related to personal injury. |
Warranty
Product warranty will expire 12+1 months after dispatch from Atlas Copco's Distribution Center.
Normal wear and tear on parts is not included within the warranty.
Normal wear and tear is that which requires a part change or other adjustment/overhaul during standard tools maintenance typical for that period (expressed in time, operation hours or otherwise).
The product warranty relies on the correct use, maintenance, and repair of the tool and its component parts.
Damage to parts that occurs as a result of inadequate maintenance or performed by parties other than Atlas Copco or their Certified Service Partners during the warranty period is not covered by the warranty.
To avoid damage or destruction of tool parts, service the tool according to the recommended maintenance schedules and follow the correct instructions.
Warranty repairs are only performed in Atlas Copco workshops or by Certified Service Partners.
Atlas Copco offers extended warranty and state of the art preventive maintenance through its ToolCover contracts. For further information contact your local Service representative.
For electrical motors:
Warranty will only apply when the electric motor has not been opened.
Website
Information concerning our Products, Accessories, Spare Parts and Published Matters can be found on the Atlas Copco website.
Please visit: www.atlascopco.com.
ServAid
ServAid is a portal that is continuously updated and contains Technical Information, such as:
Regulatory and Safety Information
Technical Data
Installation, Operation and Service Instructions
Spare Parts Lists
Accessories
Dimensional Drawings
Please visit: https://servaid.atlascopco.com.
For further Technical Information, please contact your local Atlas Copco representative.
Safety Data Sheets MSDS/SDS
The Safety Data Sheets describe the chemical products sold by Atlas Copco.
Please consult the Atlas Copco website for more information www.atlascopco.com/sds.
Country of Origin
For the Country of Origin, please refer to the information on the product label.
Dimensional Drawings
Dimensional Drawings can be found either in the Dimensional Drawings Archive, or on ServAid.
Please visit: http://webbox.atlascopco.com/webbox/dimdrw or https://servaid.atlascopco.com.
Overview
General Description
EBB26 battery drill is designed to enhance its user. Engineered to transform the pneumatic drills to battery drills, it enables operators to move faster, make fewer errors, perform better and ultimately achieve more. Being cordless allow movements without restrictions and reduces tripping hazards. Its intelligent features provide essential operator feedback, improved control and reduced risk of oversized holes. EBB26 is shaped with ergonomic as key element. Everything from weight to handle and sound levels are designed to make drilling less hard, to keep users healthy, engaged and performing at their very best.
Features
Multi speeds
Cutter wearing monitor with 3 methods
Optimized tool performance
Ergonomically maximized for drilling operation
Constant speed for best hole quality
Programmable trigger response
Wi-fi tethering function
Benefits
Shorter process time without air hoses
Reduced operational cost
Minimize fatigue and increase productive time
Reduce energy consumption and environmental impact
Reduced risk of trip hazards
System Functionality
Not available for all models.
The ToolsTalk Service 2 PC software package, is used for updating and storing software data and downloading configuration parameters to the tool. The tool is able to store and use several number of drill programs. All features in ToolsTalk Service 2 may not be available for this tool.
For more information, see ToolsTalk Service 2 User Edition user guide.
Tool Functionality
1 | Trigger |
2 | Function buttons |
3 | Display (HMI) |
4 | Front LED light |
5 | Battery |
6 | USB Port |
The tool is equipped with a display and a front LED light. Configured tool programs are stored in the tool and features can be selected for usage.
Display (HMI)
Note that depending on the model, some features and functions are not available on the tool.
Main Display
1 | Button - LEFT1 |
2 | Button - RIGHT1 |
3 | Display (HMI) |
1The position of the right or left button is based on the user holding the handle and pointing the drill away from their body.
Display at Startup
The user can switch between the cutter usage and the name by pressing the right hand button.
1A | Index of program listed and stored |
1B | Index of active program selected |
2 | Revolutions per minute |
3 | Cutter usage accumulated |
4 | Cutter usage limited |
5 | Name of the drill program |
Display Icons
Icon | Description |
|---|---|
| Battery warning |
| Temperature warning |
| Warning |
| Revolutions per minute |
| Wi-Fi Zone Tethering 1 |
| Service |
| Unlock |
| LED light ON |
| LED light OFF |
| OK - apply function |
| NOK - cancel function |
| Bin |
| Cutter usage |
1Not available for all models.
Technical Product Data
Technical Product Data can be found on either ServAid, or the Atlas Copco website.
Please visit: https://servaid.atlascopco.com or www.atlascopco.com.
Accessories
Required Accessories
Compatible Chuck
Accessory | Article Number |
|---|---|
Chuck F6.5LBA and Key | 4110 2045 80 |
Chuck Cover | 4110 2046 00 |
Tighten the chuck to 10 Nm.
Installation
Installation Requirements
Attaching and Removing the Battery Pack
Attach the battery to the tool and make sure that it is fastened correctly. The battery can be attached pointing forward or backward to get the best accessibility and balance.
To remove the battery, press the button on the battery and push it out.
Tool Upgrade
A tool upgrade can be performed by an Atlas Copco Industrial Technique AB Service technician.
Contact your Atlas Copco Industrial Technique AB representative for support and more information.
Installation Instructions
Software Installation
For installation guidelines, see ToolsTalk Service 2 User Edition user guide.
Operation
Ergonomic Guidelines
Consider your workstation as you read through this list of general ergonomic guidelines to identify areas for improvement in posture, component placement, or work environment.
Take frequent breaks and change work positions frequently.
Adapt the workstation area to your needs and the work task.
Adjust for a convenient reach range by determining where parts and tools need to be located to avoid static load.
Use workstation equipment such as tables and chairs appropriate for the work task.
Avoid work positions above shoulder level or with static holding during assembly operations.
When working above shoulder level, reduce the load on the static muscles by lowering the weight of the tool, using for example torque arms, hose reels or weight balancers. You can also reduce the load on the static muscles by holding the tool close to the body.
Take frequent breaks.
Avoid extreme arm or wrist postures, particularly during operations requiring a degree of force.
Adjust for a convenient field of vision that requires minimal eye and head movements.
Use appropriate lighting for the work task.
Select the appropriate tool for the work task.
In noisy environments, use ear protection equipment.
Use high-quality inserted tools and consumables to minimize exposure to excessive levels of vibration.
Minimize exposure to reaction forces.
When cutting:
A cut-off wheel can get stuck if the cut-off wheel is bent or not guided properly. Use the correct flange for the cut-off wheel and avoid bending the cut-off wheel during operation.
When drilling:
The drill might stall when the drill bit breaks through. Use support handles if the stall torque is high. The safety standard ISO11148 part 3 recommends using a device to absorb a reaction torque above 10 Nm for pistol grip tools and 4 Nm for straight tools.
When using direct-driven screwdrivers or nutrunners:
Reaction forces depend on the tool settings and joint characteristics. Strength and posture determine the amount of reaction force that an operator can tolerate. Adapt the torque setting to the operator's strength and posture and use a torque arm or reaction bar if the torque is too high.
In dusty environments, use a dust extraction system or wear a mouth protection mask.
Operating Instructions
Wi-Fi Zone Tethering
Not available for all models.
This tool features the Wi-Fi Zone Tethering (WZT) function, intended to make the tool less susceptible to theft.
The functionality limits the usability of the tool when it exceeds a specific Wi-Fi network or tethering zone. The tool has to be tethered to a network and can only be used for a limited time without being connected to the network, before the tool is locked. When the tool is locked it cannot be used for drilling. The tool's display will show the tool event.
When the tool is reconnected to the network again the tool is unlocked and fully operational again.
For more information to configure the Wi-Fi Tethering, see ToolsTalk Service 2 User Edition user guide.
Operating the Tool
Menu Navigation Flow
Menu Navigation Buttons
Button | Action |
|---|---|
| Press RIGHT button to navigate. |
| Press LEFT button and hold down for approximately 2 seconds. |
| Press LEFT button to select. |
Key Lock
On start up the display lock is active.
Unlock the Key Lock
Press and hold down the left hand button for approximately 2 seconds.
Once unlocked the operator can enter and navigate the menu.
Activate the Key Lock
Press the tool trigger.
OR
Do not press the button or trigger for a short while.
Operating the Drill
Press the trigger.
The selected drill program on the display will be used when the trigger is pressed.
The tool will carry out status checks before drilling can be carried out:
Temperature
Battery voltage
Internal voltage
The tool will start if all is OK.
The tool will not start the drill program if there are any discrepancies. The display will show the tool event.
Drill a hole.
While drilling, the position of the trigger is continuously used to determine the desired speed of the motor.
The tool monitors the time that the drill program has been running in order to impose a maximum time limit of 30 seconds.
End drilling
The following reasons will stop the drilling:
Stop pressing the trigger.
The drill program restrictions have been met.
Supervision limits have been met.
When the drilling ends the cutter usage and the display will be updated. If any discrepancies have occurred during drilling, it will show on the display.
Drilling Menu
Press and hold down the left menu button to unlock the display.
Select drill program by switching through the stored and active drill programs, by pressing the RIGHT button.
A scroll indicator is shown on the right hand side (white) of the display.
Display example Press the tool trigger to use the selected drill program.
Timeout
The display will timeout and revert to the startup screen if left inactive.
Resetting Cutter Usage
Select the drill program on the display .
Press and hold down the left menu button, the user will be prompted to reset cutter usage
.Press the left menu button to apply the reset
.OR
Press the right menu button to cancel
.
Example display's available when resetting cutter usage:
Cutter Usage Limit Reset
Only applicable for tools with software version 1.6.1 and later.
If cutter usage limit is reached
A notification will pop up, prompting the user to reset cutter usage.
Press the select button (left menu button) to ignore.
OR
Press down button (right menu button) to reset. A confirmation screen will appear.
Press the select button to confirm or down button to cancel.
If cutter usage limit is not reached
Navigate to the Cutter usage sub-menu and press the select button.
Scroll down the menu to find the PSET to reset and press the select button to reset. A confirmation screen will appear.
Press the select button to confirm or down button to cancel.
Front LED Light
The front LED lamp can be used to light up the target drilling area and is enabled by default.
Turn Front LED Light ON/OFF using the Tool Menu
Disable the front LED light :
Select the icon
on the display.
Enable the front LED light:
Select the icon
on the display.
For more information to configure the front LED light, see ToolsTalk Service 2 User Edition user guide.
Power Saving Mode
The tool will go on power saving mode due to inactivity. To activate the tool, press the trigger.
For more information to configure the Power Saving, see ToolsTalk Service 2 User Edition user guide.
Service Alarm
Not available for all models.
A service alarm can be set up for the tool, based on the usage of the tool or when service is required. The service alarm function will show up on the display when the tool detects the limit imposed.
The tool continuously monitors and stores data (counters) of usage set up (total usage). The tool can monitor the following usages:
Drill time (Service interval)
Drill energy (Service interval)
Lock on service alarm can be configured, where the tool will not operate once usage limit has exceeded.
Data monitored can be stored in the tool as 'Usage at last service'.
For more information to configure the Service Alarm, refer to the ToolsTalk Service 2 User Edition user guide.
Service
Preventing ESD Problems
The components inside the product and controller are sensitive to electrostatic discharge. To avoid future malfunction, make sure that service and maintenance is carried out in an ESD approved work environment. The figure below shows an example of an appropriate service work station.
Maintenance Instructions
Preventive Maintenance
Maximize Battery Life
In order to maximize battery life, do not leave the battery connected to the tool if you do not plan to use it for several days. The battery can discharge and go into “sleep mode” which will require a special wake-up charge procedure.
Overhaul
Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
Service must only be carried out by qualified personnel who have access to the Service instruction and/or have been trained for service on (these specific) EBB and EBP tools.
The electric motor is a sealed unit and may under no circumstances be opened by anyone else than Atlas Copco Industrial Technique AB.
Overhaul and preventive maintenance is recommended at regular intervals once per year or after maximum 250.000 drilling cycles depending on which occurs sooner. More frequent overhaul may be needed if the machine is used in heavy-duty operations. If the machine not is working properly, it should immediately be taken away for inspection.
When dismantling the tool always use the specially designed service tool 4080 0848 80, (two service tools are required).
Lubrication Instructions
Lubrication
Lubricate gears with grease containing molybdenum disulphide (e.g. Molykote BR2 Plus). Lubricate o-rings and threaded connections with grease (e.g. Almagard LE 3751) before assembling.
Brand | Type |
|---|---|
Molykote | BR2 Plus |
Almagard | LE 3751
|
Dismantling/Assembling Instructions
Assembling the Chuck
Place the front part module in the plastic clamps (4080 1133 80) and put it in a vice.
Use a 15 mm spanner (4006 3597 00) and an adapter in the chuck.
Tighten the chuck to 10 Nm.
Assembling the Planetary Gear
Front Part Assembly
Insert the 2 O-rings (4 and 5) into the front part (3).
Insert the gear rim (6) into the front part (3).
Assemble the washer (9) and wave washer (10) onto the shaft (8).
Press the ball bearing (11) onto the shaft (8).
Mount the snap ring (12) onto the shaft (8).
Insert the plug (2) into the front part (3).
Insert the assembled shaft (8) into the front part (3).
Press the ball bearing into the front part
Use the press tool 4080 1131 00 and 4080 1132 00.
Place the mounting tool on the press.
Put the front part, facing upwards, on the mounting tool.
Place the second part of the mounting tool on top of the front part.
Make sure to place the mounting tool so that it presses both the inner and outer ring of the bearings.
Push down the press.
Press the front part and mounting tool together.
Make sure the front part has a flush surface.
Tighten the distance ring (7) onto the shaft (8) to 15 Nm.
Updating the Tool Software
Not available for all models.
For information on updating the tool software, refer to the Copying Firmware section in the ToolsTalk Service 2 User Edition user guide.
To prevent damage to the tool:
Make sure the battery is fully charged when performing a software update.
Do not remove the battery from the tool while the software update is in progress.
Software Update Status
Not available for all models.
During configuration and software update the tool shows limited content on the display, compared to normal operation.
Light behavior | State | Meaning |
|---|---|---|
Flashing blue | Boot/Configuration mode | A USB cable has been plugged into the tool. The tool is in boot/configuration mode and is/or is ready to be connected to ToolsTalk 2 Service. |
Flashing green | Software update progressing | A software update is in progress. |
Flashing red | Error | The tool has encountered an error during software update or boot up. Connect the tool to ToolsTalk 2 Service for more information. |
Troubleshooting
Troubleshooting Tool Events
Tool events which appears on the display:
Icon display | Light | Event | Tool behaviors |
|---|---|---|---|
| Flashing red | Overheated | The tool will not start drilling. |
| Steady red | Battery empty | The tool will not start drilling. |
| Flashing red | Cutter usage [limit exceeded - no lock] | The tool will start drilling. |
| Steady red | Cutter usage [limit exceeded - lock] | The tool will not start drilling. |
| Flashing red | Service [limit reached - no lock] | The tool will start drilling. |
| Steady red | Service [limit reached - lock] | The tool will not start drilling. |
| Steady red | Wi-Fi Zone Tethering.1 Out of range. | The tool will not start drilling. |
| Steady red | Unrecoverable error:
| The tool will not start drilling. Connect to ToolsTalk 2 Service. |
| Flashing red | Recoverable error:
| The tool will not start drilling. The reason for the event/state will go away. |
1Not available for all models.
Overheated Tool
The tool is designed for normal handheld drilling. The tool temperature can be influenced by the following parameters:
Thickness of the material
Type of material
Drilling diameter
Pre-hole size
Drill bit geometry
Rest time between each hole
Thrust force from operator
Number of holes in a series
Recycling
Environmental Regulations
When a product has served its purpose it has to be recycled properly. Dismantle the product and recycle the components in accordance with local legislation.
Batteries shall be taken care of by your national battery recovery organization.
Recycling Instruction
Position | Part | Remarks | Recycle as |
|---|---|---|---|
1 | Front cover | Metal, Steel | |
2 | Marking plate | Metal, Steel | |
3 | Handle | Right | Plastic, Other, PA6GF30 |
4 | Screws | 4 pcs | Metal, Steel |
5 | Motor housing, complete | Electronics | |
6 | Handle and trigger | Left | Plastic, Other, PA6GF30 |
7 | Display (HMI) and radio board module | Electronics | |
8 | Main board | Electronics | |
9 | Battery connector | Plastic, Other, PA6 | |
10 | Screws | 2 pcs | Metal, Steel |