Event codes
Error code | Event information | Instruction |
|---|---|---|
101 | Supply voltage exceeded | Check power supply. |
102 | Supply voltage too low | Check power supply. |
103 | Internal 24V exceeded | Disconnect external equipment. |
104 | Internal 24V too low | Disconnect external equipment. |
105 | Internal 12V exceeded | Disconnect tool if connected. |
106 | Internal 12V too low | Disconnect tool if connected. |
107 | Internal 5V exceeded | Disconnect tool if connected. |
108 | Internal 5V too low | Disconnect tool if connected. |
109 | External 24V error | Disconnect external equipment, restart controller. |
110 | DC/DC temperature error | Replace the controller. |
111 | I/O expanders reinitialized | Press OK to continue. |
112 | Failed to reinitialize I/O | Restart the controller. |
113 | Power fault | Check power supply. |
120 | Zero offset error, Current | Replace the controller. |
121 | Zero offset error, Sensor | Replace the tool transducer or the tool. |
122 | Motor current low | Replace the tool. |
123 | Motor current exceeded | Replace the tool. |
124 | Motor driver voltage too low | Replace the tool. |
125 | Motor driver short circuit | Replace the tool. |
126 | Motor driver temperature exceeded | Replace the tool. |
127 | Motor driver open load | Replace the tool. |
128 | Motor driver fault | Restart the controller. |
130 | EEPROM read error | Replace the controller. |
131 | EEPROM write error | Replace the controller. |
132 | Internal hardware error | Replace the controller. |
133 | File system error | Replace IAM MT. |
134 | USB host overcurrent | Disconnect USB devices. |
135 | USB flash drive volume error | Try another USB flash drive. |
140 | No tool connected | Connect tool. |
141 | Tool not supported | Connect supported tool. |
142 | Tool communication error | Replace the tool. |
143 | Tool 5V error | Replace the tool. |
144 | Tool 12V error | Replace the tool. |
150 | Tool initializing error | Check that the tool is running freely during start up. |
151 | Friction too high | Check that the tool is running freely during start up. |
152 | Tool angle encoder error | Connect tool. |
153 | Tool direction error | Connect tool. |
154 | Bit was blocked | Check that the tool is running freely during start up. |
155 | Tool motor temperature exceeded | Allow time for tool to cool down. |
156 | Tool not supported | Transducerized tools not supported by current license. |
157 | Failed to update tool software | Disconnect transducer. |
158 | Tool initialization error | |
159 | Torque measurement warning | Calibrate the tool. |
160 | Torque measurement error | Calibrate the tool. |
201 | Runtime parameter error | Restart the controller. |
202 | Invalid controller parameters | Replace IAM MT. |
203 | Invalid controller parameters | Replace the tool |
204 | Invalid I/O parameters | Replace IAM MT. |
205 | Invalid identifier parameters | Replace IAM MT. |
206 | Invalid Pset parameters | Replace IAM MT. |
207 | Invalid Batch sequence parameters | Replace IAM MT. |
208 | Invalid password parameters | Replace IAM MT. |
209 | Tool statistics error. | Replace the tool. |
210 | Unable to load fonts from IAM MT | Replace IAM MT. |
211 | Invalid tool configuration parameters | Replace IAM MT. |
212 | Invalid operator parameters | Replace IAM MT. |
220 | Result database error | Replace IAM MT. |
221 | Graph database error | Replace IAM MT. |
225 | Reset result database | Result database was reset. |
226 | Reset graph database | Graph database was reset. |
227 | No results to export - database empty | |
228 | Old results removed | |
229 | Old graphs removed | |
230 | Pset not configured for connected tool | Select another Pset or configure new Pset in ToolsTalk MT. |
231 | Select error source | Change select source. Can be changed in ToolsTalk MT Controller settings. |
232 | Select error busy | Wait until tool is not running. |
240 | Network configuration has an error | Change network configuration. |
241 | IP address and gateway not in same subnet | Change network configuration. |
301 | Tool connected | Press OK to initialize the tool. |
302 | Tool initializing | Please wait. |
303 | Tool software updating | Please wait. |
304 | Tool software update error | Check tool cable or replace the tool. |
305 | Tool calibration required | Calibrate the tool. |
306 | Service required | Tool calibration has expired. Calibrate the tool. |
310 | Software has been updated | Press OK to continue. |
311 | Software file wasn't found on USB | Copy software file to USB flash drive. |
312 | Software update failed | Software file on USB may be broken. Update software file on USB and try again. |
313 | Copying software | Please wait. Software is being copied to/from USB. |
314 | Can only show first 20 .mtp or .fw files | Press OK to continue. |
315 | Software update failed - incompatible hardware | |
320 | Login expired | User was logged out. |
321 | User has logged in | |
322 | The current user has logged out | |
350 | Battery adapter hardware error | |
351 | Battery adapter temperature exceeded | Let battery to cool down. |
352 | Battery adapter charge fault | Change battery. |
353 | Battery temperature error | Let battery to cool down. |
354 | Battery discharge error | Connect PSU to charge battery. |
355 | Battery charge critically low | Connect PSU to charge battery. |
356 | Battery not supported | Change battery. |
357 | Battery adapter charge fault | Change battery. |
358 | Battery adapter charge fault | Let battery cool down or change battery. |
401 | Tightening error | Press OK to continue |
402 | Batch sequence error | Press OK to continue |
403 | Batch sequence parameter error | Check controller to see which parameter is incorrect |
404 | Pset not supported | Select another Pset |
405 | Pset parameter error | Update Pset. |
507 | ToolsNet skipped result | |
601 | Controller communication error | |
602 | Transducer communication error | |
603 | Measurement data lost due to lost USB link | |
604 | Transducer connected | |
605 | No transducer detected | Connect transducer and try again. |
606 | Remote device is busy | Try again later. |
607 | Transducer service required | |
608 | Zero offset error, Transducer | Check that the transducer cable is fastened correctly or replace cable/transducer. |
609 | Operator ID required by active verification | Scan operator ID. |
610 | Connected device is not compatible with QA | |
701 | Fieldbus not supported by controller HW | Replace controller with rev C or higher. |
702 | Invalid fieldbus parameters | Replace IAM MT. |
703 | Fieldbus module error | Check fieldbus cable or replace the fieldbus module, press OK to continue. |
704 | Fieldbus driver warning | Check for firmware update, press OK to continue. |
705 | Fieldbus driver error | Check for firmware update. |
706 | Fieldbus module in error state | Check fieldbus network status. |
707 | Fieldbus module in exception state | Check for firmware update. |
720 | Fieldbus module not connected | Connect fieldbus module, check fieldbus cable or replace the fieldbus module. |
721 | Fieldbus module not supported, wrong module type | Connect supported fieldbus module. |
722 | Fieldbus module not supported, wrong network type | Connect supported fieldbus module. |
723 | Fieldbus module not supported, wrong provider ID | Connect supported fieldbus module. |
724 | Fieldbus module not supported, FW version not approved | Connect supported fieldbus module. |
730 | Fieldbus not configured for connected module | Change configuration of fieldbus type or connect correct module. |
731 | Fieldbus parameter error | Update fieldbus parameters and press OK. |
732 | Fieldbus configuration of network settings failed | Check that fieldbus setup is ok and try again. |
740 | Max 128 submodules supported for Profinet | Update fieldbus parameters and press OK. |
741 | Profinet station name syntax error | Update fieldbus parameters and press OK. |
901 | IAM MT not present | Insert IAM MT. |
902 | Failed to initialize IAM MT | Restart controller or change IAM MT. |
903 | IAM MT read error | Check that the FW file on the IAM MT root is named exactly MTF6000.FW (manually from PC). Otherwise replace the IAM MT. |
904 | IAM MT write error | Replace IAM MT. |
905 | Invalid software on IAM MT | Update software on IAM MT (manually from PC). |
906 | Flash programming error | Replace the controller. |
907 | Invalid license on IAM MT | Update software on IAM MT (manually from PC) to a newer version that support the IAM license. Otherwise replace the IAM MT. |
908 | Incompatible software version | Update software on IAM MT (manually from PC) to a newer version that supports the HW. Otherwise replace the IAM MT. |
990 | External event | |
991 | External event | |
992 | External event |
