EM Stop Connector Configurations
The following EM Stop connector configurations are possible:
EM Stop default configuration (no EM Stop connected).
EM Stop entry configuration - single controller with hand-held tools.
EM Stop entry configuration - multiple controllers with hand-held tools.
EM Stop entry configuration - single controller with fixtured tools.
EM Stop entry configuration - multiple controllers with fixtured tools.
EM Stop entry configuration - single controller without manual reset.
EM Stop bypass configuration.
EM Stop loopback configuration.
EM Stop Default Configuration
WARNINGFor this configuration, the remote start enable switch must be set to OFF
The POWER FOCUS 8 comes with preinstalled jumpers for this configuration.
Use the following pin configuration:
Pin | Pin name | Use |
|---|---|---|
1 | EM_NC1 | Do not use |
2 | EM_STOP+ | Do not use |
3 | EM_STOP+ | Connect a jumper between pin 3 and pin 4 |
4 | 24V_ISOL_EXT | See pin 3 |
5 | EM_STOP- | Connect a jumper between pin 5 and pin 6 |
6 | GND | See pin 5 |
7 | EM_BYPASS_STOP- | Do not use |
8 | EM_BYPASS_NC | Do not use |
9 | EM_RESET_IN | Connect a jumper between pin 9 and pin 10 |
10 | EM_NC2 | See pin 9 |
EM Stop Entry Configuration - Single Controller with Hand-held Tools
For this configuration, the software reset must be set to OFF.
EM Stop button connector: Phoenix, 10-pin headers, 3.5 mm pitch
Use the following pin configuration:
Pin | Pin name | Use |
|---|---|---|
1 | EM_NC1 | Connect a jumper between pin 1 and pin 2 |
2 | EM_STOP+ | See pin 1 |
3 | EM_STOP+ | Connect an emergency button between pin 3 and pin 4 |
4 | 24V_ISOL_EXT | See pin 3 |
5 | EM_STOP- | Connect an emergency button between pin 5 and pin 6 |
6 | GND | See pin 5 |
7 | EM_BYPASS_STOP- | Do not use |
8 | EM_BYPASS_NC | Do not use |
9 | EM_RESET_IN | Connect a reset button between pin 9 and 10 |
10 | EM_NC2 | See pin 9 |
EM Stop Entry Configuration - Multiple Controllers with Hand-held Tools
For this configuration, the software reset must be set to OFF.
Pin | Pin name | Use |
|---|---|---|
1 | EM_NC1 | Connect a jumper between pin 1 and pin 2 |
2 | EM_STOP+ | See pin 1 |
3 | EM_STOP+ | Connect an emergency button between pin 3 and pin 4 |
4 | 24V_ISOL_EXT | See pin 3 |
5 | EM_STOP- | Connect an emergency button between pin 5 and pin 6 |
6 | GND | See pin 5 |
7 | EM_BYPASS_STOP- | Do not use |
8 | EM_BYPASS_NC | Connect a reset button between pin 8 and 9 |
9 | EM_RESET_IN | See pin 8 |
10 | EM_NC2 | Do not use |
EM Stop Entry Configuration - Single Controller with Fixtured Tools
For this configuration, the remote start enable switch must be set to ON and the software reset must be set to OFF.
Pin | Pin name | Use |
|---|---|---|
1 | EM_NC1 | Connect a jumper between pin 1 and pin 2 |
2 | EM_STOP+ | See pin 1 |
3 | EM_STOP+ | Connect an emergency button between pin 3 and pin 4 |
4 | 24V_ISOL_EXT | See pin 3 |
5 | EM_STOP- | Connect an emergency button between pin 5 and pin 6 |
6 | GND | See pin 5 |
7 | EM_BYPASS_STOP- | Do not use |
8 | EM_BYPASS_NC | Do not use |
9 | EM_RESET_IN | Connect a reset button between pin 9 and 10 |
10 | EM_NC2 | See pin 9 |
EM Stop Entry Configuration - Multiple Controllers with Fixtured Tools
For this configuration, the remote start enable switch must be set to ON and the software reset must be set to OFF.
Pin | Pin name | Use |
|---|---|---|
1 | EM_NC1 | Connect a jumper between pin 1 and pin 2 |
2 | EM_STOP+ | See pin 1 |
3 | EM_STOP+ | Connect an emergency button between pin 3 and pin 4 |
4 | 24V_ISOL_EXT | See pin 3 |
5 | EM_STOP- | Connect an emergency button between pin 5 and pin 6 |
6 | GND | See pin 5 |
7 | EM_BYPASS_STOP- | Do not use |
8 | EM_BYPASS_NC | Connect a reset button between pin 8 and 9 |
9 | EM_RESET_IN | See pin 8 |
10 | EM_NC2 | Do not use |
EM Stop Entry Configuration - Single Controller without Manual Reset
For this configuration, the software reset must be set to ON.
EM Stop button connector: Phoenix, 10-pin headers, 3.5 mm pitch
Use the following pin configuration:
Pin | Pin name | Use |
|---|---|---|
1 | EM_NC1 | Do not use |
2 | EM_STOP+ | Do not use |
3 | EM_STOP+ | Connect an emergency button between pin 3 and pin 4 |
4 | 24V_ISOL_EXT | See pin 3 |
5 | EM_STOP- | Connect an emergency button between pin 5 and pin 6 |
6 | GND | See pin 5 |
7 | EM_BYPASS_STOP- | Do not use |
8 | EM_BYPASS_NC | Do not use |
9 | EM_RESET_IN | Connect a jumper between pin 9 and pin 10 |
10 | EM_NC2 | See pin 9 |
EM Stop Bypass Configuration
EM Stop I/O cable connector: Phoenix, 10-pin
Remove plug or use the following pin configuration:
Pin | Pin name | Use |
|---|---|---|
1 | EM_NC1 | Do not use |
2 | EM_STOP+ | Do not use |
3 | EM_STOP+ | Do not use |
4 | 24V_ISOL_EXT | Do not use |
5 | EM_STOP- | Do not use |
6 | GND | Do not use |
7 | EM_BYPASS_STOP- | Do not use |
8 | EM_BYPASS_NC | Do not use |
9 | EM_RESET_IN | Do not use |
10 | EM_NC2 | Do not use |
EM Stop loopback configuration
EM Stop I/O cable connector: Phoenix, 10-pin
Use the following pin configuration:
Pin | Pin name | Use |
|---|---|---|
1 | EM_NC1 | Do not use |
2 | EM_STOP+ | Do not use |
3 | EM_STOP+ | Do not use |
4 | 24V_ISOL_EXT | Do not use |
5 | EM_STOP- | Do not use |
6 | GND | Do not use |
7 | EM_BYPASS_STOP- | Do not use |
8 | EM_BYPASS_NC | Connect a jumper between pin 8 and pin 10 |
9 | EM_RESET_IN | Do not use |
10 | EM_NC2 | See pin 8 |
