NOK Results List
Error message | Description | GUI location |
|---|---|---|
Drive error | Internal driver error or driver loss detected. | N/A |
Rehit | Attempt to tighten an already tightened bolt. | Tightening parameters (Edit) > Rehit detection |
Soft start torque below min | Soft start torque below minimum level. | [Four Step] Tightening parameters (Edit) > (Step 1) Soft Start > Torque min |
Soft start torque above max | Soft start torque exceeded maximum level. | Tightening parameters (Edit) > (Step 1) Soft Start > Torque max |
Selftap torque above max | Selftap torque exceeded maximum level. | Tightening parameters (Edit) > (Step 2) Selftap > Torque max |
Selftap torque below min | Selftap torque below minimum limit. | Tightening parameters (Edit) > (Step 2) Selftap > Torque min |
Safety torque limit low | Automatically calculated torque value to ensure torque sensor is mounted correctly. | N/A |
Rundown torque above max | Rundown torque exceeded maximum level. | Tightening parameters (Edit) > (Step 2) Rundown torque limits > Torque max |
Rundown angle above max | Rundown angle exceeded maximum level. | Tightening parameters (Edit) > (Step 2) Rundown angle limits > Angle max |
Rundown exceeded max time limit | Rundown time exceeded maximum limit. | Tightening parameters (Edit) > (Step 2) Rundown angle limits > Time max |
Rundown below min time limit | Rundown time below minimum limit. | Tightening parameters (Edit) > (Step 2) Rundown angle limits > Time min |
Rundown torque below min | Rundown torque below minimum level. | Tightening parameters (Edit) > (Step 2) Rundown torque limits > Torque min |
Rundown angle below min | Rundown angle below minimum level. | Tightening parameters (Edit) > (Step 2) Rundown angle limits > Angle min |
Final step torque above max | Final step torque exceeded maximum level. | Tightening parameters (Edit) > (Step 3) Final step > Torque limits Manual > Torque max |
Final step angle above max | Final step angle exceeded maximum level. | Tightening parameters (Edit) > (Step 3) Final step > Angle max |
Final step torque below min | Final step torque below minimum level. | Tightening parameters (Edit) > (Step 3) Final step > Torque limits Manual > Torque min |
Final step angle below min | Final step angle below minimum level. | Tightening parameters (Edit) > (Step 3) Final step > Angle max |
Tightening timeout | Tightening time limit exceeded. | [Multistep] Tightening parameters (Edit) > Step dependent [Other tightening programs]: fixed parameter set to 30 seconds |
Trigger lost | Tool trigger was released before target was reached. | [Multistep]: trigger release before tightening step target has been reached [Other tightening programs]: trigger release before tightening stage has finished |
Slip off | Socket has slipped off the nut. | Tightening parameters (Edit) > (Step 3) Tightening parameters > Slipoff detection time |
Target reached before final step | Target torque reached before final step in tightening program. | Target torque |
Post view torque below min | Post view torque below minimum level. | Tightening parameters (Edit) > (Step 2) Post view torque > Torque min |
Post view torque above max | Post view torque exceeded maximum level. | Tightening parameters (Edit) > (Step 2) Post view torque > Torque max |
Post view torque interval not reached | Post view torque interval not reached. | Tightening parameters (Edit) > (Step 2) Post view torque > Torque min length |
Torque compensation interval not reached | Torque compensation interval angle before rundown end not reached. | Tightening parameters (Edit) > (Step 3) Torque compensation > Torque compensation point |
Tool movement exceeded | Tool was moved beyond set angle limits. | Tightening parameters (Edit) > (Step 1) TrueAngle compensation (On); Tool movement limits > Positive/Negative |
Current monitoring error | Current monitoring error. | Tightening parameters (Edit) > (Step 1) Current monitoring (On) |
Soft start angle above max | Soft start angle exceeded maximum level. | [Four Step] Tightening parameters (Edit) > (Step 1) Soft start > Angle max |
Soft start angle below min | Soft start angle below minimum level (Four Step). | [Four Step] Tightening parameters (Edit) > (Step 1) Soft start > Angle min |
First step angle high | First step angle exceeded maximum level (Four Step). | [Four Step] Tightening parameters (Edit) > (Step 3) First step > First angle max |
First step angle low | First step angle below minimum level (Four Step). | [Four Step] Tightening parameters (Edit) > (Step 3) First step > First angle min |
First step torque high | First step torque exceeded maximum level (Four Step). | [Four Step] Tightening parameters (Edit) > (Step 3) First step > First torque max |
First step torque below min | First step torque below minimum level (Four Step). | [Four Step] Tightening parameters (Edit) > (Step 3) First step > First torque min |
First step exceeded max time limit | First step time exceeded maximum level (Four Step). | [Four Step] Tightening parameters (Edit) > (Step 3) First step > Time max |
First step below min time limit | First step time below minimum level (Four Step). | [Four Step] Tightening parameters (Edit) > (Step 3) First step > Time min |
Final step exceeded max time limit | Final step time exceeded maximum level (Four Step). | [TurboTight, Four Step] Tightening parameters (Edit) > (Step 3) Final step > Time max |
Final step below min time limit | Final step time below minimum level (Four Step). | [TurboTight, Four Step] Tightening parameters (Edit) > (Step 3) Final step > Time min |
Low torque at final supervision | Final Supervision Torque was not reached. | [Four Step] Tightening parameters (Edit) > (Step 3) Torque limits (manual) > Torque min |
Soft start exceeded max time limit | Soft start time exceeded maximum level (Four Step). | [Four Step] Tightening parameters (Edit) > (Step 1) Soft start > Time max |
TurboTight time limit exceeded | TurboTight time limit exceeded. | [TurboTight] Tightening parameters (Edit) > (Step 3) Final step > Time max |
Snug monitor high | Wrench only. Monitor detected snug value exceeded. | Tightening parameters (Edit) > Rundown stage (Step 2) Rundown complete > Rundown complete torque |
No residual torque | Wrench only. Residual torque was under threshold. | [TurboTight] + [TensorPulse] Tightening parameters (Edit) > (Step 3) > Tightening parameters > Residual torque correlation factor |
Overspeed | Wrench only. Wrench gyro failed to measure angle due to high speed. | N/A |
