Revision History

Release Number

Revision Date

Revision Description

3.6

06/2021

UPDATED content:

DELETED content:

  • Four step tightening strategy

3.5

12/2020

Added or updated paragraphs:

  • Updated "Multistep Programs > Tightening Steps" paragraph

  • Updated "Multistep Programs > Step Monitors" paragraph

  • Updated "Multistep Programs > Step Restrictions" paragraph

  • Updated "Multistep Programs > Result Reporters" paragraph

  • Updated "Trigger Lost" paragraph

  • Added "Configuring Result Presentation Settings" paragraph

  • Added "Show Final Torque with PrT Compensation: ON / Show PrT Compensation Value on Live Result: ON" paragraph

  • Added "Show Final Torque with PrT Compensation: OFF / Show PrT Compensation Value on Live Result: ON" paragraph

  • Added "Show Final Torque with PrT Compensation: OFF / Show PrT Compensation Value on Live Result: OFF" paragraph

  • Added "Show Final Torque with PrT Compensation: ON / Show PrT Compensation Value on Live Result: OFF" paragraph

  • Updated "StepSync Signals > Input Signals" paragraph

  • Updated "StepSync Signals > Output Signals" paragraph

  • Updated "Configuring the ToolsTalk Connection" paragraph

  • Updated "Configuring the ToolsNet Connection" paragraph

  • Updated "Configuring the PIN" paragraph

  • Updated "Clear Results" paragraph

  • Added "Viewing Protocol Status" paragraph

  • Updated "Stored Results" paragraph

  • Added "Viewing Synchronized Traces" paragraph

  • Updated "Event Codes" paragraph

  • Added "SPC - Statistics Process Control" paragraph

  • Added "Configuring SPC Parameters" paragraph

  • Added "Configuring SPC Variables" paragraph

  • Added "Calculating Statistics" paragraph

  • Added "Viewing Statistics Results" paragraph

  • Updated "Input Signals" paragraph

  • Updated "Output Signals" paragraph

  • Updated "Input/Output Signals" paragraph

3.4

Added or updated paragraphs:

  • Updated "Software" paragraph

  • Updated "Export/Import" paragraph

  • Added "Exporting "All Controller Information"" paragraph

  • Added "Exporting "Settings and Configurations"" paragraph

  • Added "Exporting "Logs from Connected Tools"" paragraph

  • Added "Exporting "Results"" paragraph

  • Added "Importing Controller Configurations and Settings" paragraph

  • Added "Automated Backup" paragraph

  • Added "Supported Tools" paragraph

  • Updated " Tightening Steps" paragraph

  • Updated "Tool Motor Tuning" paragraph

  • Added "Open End Tuning" paragraph

  • Updated "Settings for a Multistep Program" paragraph

  • Added "Trace Setting" paragraph

  • Added "Setting up the Firewall" paragraph

  • Updated "General Virtual Station" paragraph

  • Updated "Configuration of the Direction Switch" paragraph

  • Updated "Event Codes" paragraph

  • Updated "Stored Results" paragraph

3.3

Added or updated paragraphs:

  • Updated "TrueAngle Compensation" paragraph

  • Updated "STwrench" paragraph

  • Updated "Configuration of the PIN Settings" paragraph

  • Added "Running the External Result Tightening Strategy with a Tool Connected" paragraph

  • Added "Running the External Result Tightening Strategy without a Tool Connected" paragraph

  • Updated "Tool Configuration" paragraph

  • Updated "TAG Check" paragraph

  • Updated "TAG Selection" paragraph

  • Added "Input Signals" paragraph

  • Added "Output Signals" paragraph

  • Added "Input/Output Signals" paragraph

  • Updated "Tightening Steps" paragraph

  • Updated "Step Monitors" paragraph

  • Updated "Step Restrictions" paragraph

  • Added "Result Reporters" paragraph

  • Updated "Settings for a Multistep Program" paragraph

  • Added "Result View - Result Reporter" paragraph

  • Updated "Emergency Stop" paragraph

3.1.X

Added or updated sections:

  • Updated Fieldbus Configuration settings

  • Updated General Virtual Station - Unlock tool on loosening

  • Updated Event Codes

3.1

Added or updated sections:

  • Updated license management

  • Copying pasting of tightening programs

  • Updated signal

  • Updated third party licenses

3.0

Added or updated sections:

  • License (FMS) chapter

  • StepSync chapter

  • Updated Multistep

  • Apply and Undo button for Tightening and Source Tightening

2.8

Added or updated sections:

  • Calibration using STa6000 or STpad

  • Configurable job counter

  • Decrement on OK

  • Scanner pass-through

2.7

Added or updated sections:

  • Updated multistep steps

  • Source Batch (barcode scanning)

  • Updated Event Codes for SRB and TBP tools

2.6

Added or updated sections

  • Multistep tightening strategy (Editor)

  • WLAN and Bluetooth for wireless tools

2.5

Added or updated sections:

  • Multistep tightening strategy

  • Selector confirm

  • Saved positions

  • General virtual station

  • Wifi socket selector

  • Multiple PINs

  • External OK

  • Service alarms for pulse tools

  • Manual mode virtual station

2.4

Added or updated sections:

  • Settings: License manager

  • Settings: PIN code

  • Settings: Configure start screen

  • Tightening: Disable tightening, Measure angle to, Trigger lost, Torque tuning factor

  • Tool health and battery check

  • Controller health and battery check

  • Pulse strategies

  • 3-step tightening

  • Device: Accessory bus

  • Device: Led ring

  • Device: EHMI

  • Device: Fieldbus diagnostics

  • Export/Import

2.3

Added or updated sections:

  • System settings: network configuration

  • System settings: preferences

  • System settings: protocol configuration

  • System settings: tightening

  • Tightening: Time monitoring and Torque tuning factor

  • ST Wrench

  • Sources

  • Accessory configuration: tool configuration, start condition, and socket selector configuration

  • System administration: Export/Import

  • Tool configuration; ST Wrench

  • Appendix A: Front connections

2.1

Added or updated sections:

  • Settings: Fieldbus

  • Controller menu - Tightening: Current monitoring and True angle compensation

  • Four step tightening

  • System administration: Exported csv file format

  • Virtual station: I/O diagnostics and Fieldbus

  • Appendix A: Emergency stop

2.0

Added or updated sections:

  • Settings: Tool alarms

  • Tool configuration: Tool connection, Tool maintenance, Internal Wlan for wireless tools

  • Tightening setup: Loosening step

  • Tightening results: Live results, Stored results, Status for NOK results

  • Virtual station

  • Event codes in Power Focus 6000

1.6

First official release of the configuration guide for Power Focus 6000.