Revision History

3.5

Added or updated paragraphs:

• Updated "Multistep Programs > Tightening Steps" paragraph

• Updated "Multistep Programs > Step Monitors" paragraph

• Updated "Multistep Programs > Step Restrictions" paragraph

• Updated "Multistep Programs > Result Reporters" paragraph

• Updated "Trigger Lost" paragraph

• Added "Configuring Result Presentation Settings" paragraph

• Added "Show Final Torque with PrT Compensation: ON / Show PrT Compensation Value on Live Result: ON" paragraph

• Added "Show Final Torque with PrT Compensation: OFF / Show PrT Compensation Value on Live Result: ON" paragraph

• Added "Show Final Torque with PrT Compensation: OFF / Show PrT Compensation Value on Live Result: OFF" paragraph

• Added "Show Final Torque with PrT Compensation: ON / Show PrT Compensation Value on Live Result: OFF" paragraph

• Updated "StepSync Signals > Input Signals" paragraph

• Updated "StepSync Signals > Output Signals" paragraph

• Updated "Configuring the ToolsTalk Connection" paragraph

• Updated "Configuring the ToolsNet Connection" paragraph

• Updated "Configuring the PIN" paragraph

• Updated "Clear Results" paragraph

• Added "Viewing Protocol Status" paragraph

• Updated "Stored Results" paragraph

• Added "Viewing Synchronized Traces" paragraph

• Updated "Event Codes" paragraph

• Added "SPC - Statistics Process Control" paragraph

• Added "Configuring SPC Parameters" paragraph

• Added "Configuring SPC Variables" paragraph

• Added "Calculating Statistics" paragraph

• Added "Viewing Statistics Results" paragraph

• Updated "Input Signals" paragraph

• Updated "Output Signals" paragraph

• Updated "Input/Output Signals" paragraph

3.4

Added or updated paragraphs:

• Updated "Software" paragraph

• Updated "Export/Import" paragraph

• Added "Exporting "All Controller Information"" paragraph

• Added "Exporting "Settings and Configurations"" paragraph

• Added "Exporting "Logs from Connected Tools"" paragraph

• Added "Exporting "Results"" paragraph

• Added "Importing Controller Configurations and Settings" paragraph

• Added "Automated Backup" paragraph

• Added "Supported Tools" paragraph

• Updated " Tightening Steps" paragraph

• Updated "Tool Motor Tuning" paragraph

• Added "Open End Tuning" paragraph

• Updated "Settings for a Multistep Program" paragraph

• Added "Trace Setting" paragraph

• Added "Setting up the Firewall" paragraph

• Updated "General Virtual Station" paragraph

• Updated "Configuration of the Direction Switch" paragraph

• Updated "Event Codes" paragraph

• Updated "Stored Results" paragraph

3.3

Added or updated paragraphs:

• Updated "TrueAngle Compensation" paragraph

• Updated "STwrench" paragraph

• Updated "Configuration of the PIN Settings" paragraph

• Added "Running the External Result Tightening Strategy with a Tool Connected" paragraph

• Added "Running the External Result Tightening Strategy without a Tool Connected" paragraph

• Updated "Tool Configuration" paragraph

• Updated "TAG Check" paragraph

• Updated "TAG Selection" paragraph

• Added "Input Signals" paragraph

• Added "Output Signals" paragraph

• Added "Input/Output Signals" paragraph

• Updated "Tightening Steps" paragraph

• Updated "Step Monitors" paragraph

• Updated "Step Restrictions" paragraph

• Added "Result Reporters" paragraph

• Updated "Settings for a Multistep Program" paragraph

• Added "Result View - Result Reporter" paragraph

• Updated "Emergency Stop" paragraph

3.1.X

Added or updated sections:

• Updated Fieldbus Configuration settings

• Updated General Virtual Station - Unlock tool on loosening

• Updated Event Codes

3.1

Added or updated sections:

• Updated license management

• Copying pasting of tightening programs

• Updated signal

• Updated third party licenses

3.0

Added or updated sections:

• License (FMS) chapter

• StepSync chapter

• Updated Multistep

• Apply and Undo button for Tightening and Source Tightening

2.8

Added or updated sections:

• Calibration using STa6000 or STpad

• Configurable job counter

• Decrement on OK

• Scanner pass-through

2.7

Added or updated sections:

• Updated multistep steps

• Source Batch (barcode scanning)

• Updated Event Codes for SRB and TBP tools

2.6

Added or updated sections

• Multistep tightening strategy (Editor)

• WLAN and Bluetooth for wireless tools

2.5

Added or updated sections:

• Multistep tightening strategy

• Selector confirm

• Saved positions

• General virtual station

• Wifi socket selector

• Multiple PINs

• External OK

• Service alarms for pulse tools

• Manual mode virtual station

2.4

Added or updated sections:

• Settings: License manager

• Settings: PIN code

• Settings: Configure start screen

• Tightening: Disable tightening, Measure angle to, Trigger lost, Torque tuning factor

• Tool health and battery check

• Controller health and battery check

• Pulse strategies

• 3-step tightening

• Device: Accessory bus

• Device: Led ring

• Device: EHMI

• Device: Fieldbus diagnostics

• Export/Import

2.3

Added or updated sections:

• System settings: network configuration

• System settings: preferences

• System settings: protocol configuration

• System settings: tightening

• Tightening: Time monitoring and Torque tuning factor

• ST Wrench

• Sources

• Accessory configuration: tool configuration, start condition, and socket selector configuration

• System administration: Export/Import

• Tool configuration; ST Wrench

• Appendix A: Front connections

2.1

Added or updated sections:

• Settings: Fieldbus

• Controller menu - Tightening: Current monitoring and True angle compensation

• Four step tightening

• System administration: Exported csv file format

• Virtual station: I/O diagnostics and Fieldbus

• Appendix A: Emergency stop

2.0

Added or updated sections:

• Settings: Tool alarms

• Tool configuration: Tool connection, Tool maintenance, Internal Wlan for wireless tools

• Tightening setup: Loosening step

• Tightening results: Live results, Stored results, Status for NOK results

• Virtual station

• Event codes in Power Focus 6000

1.6

First official release of the configuration guide for Power Focus 6000.