Multistep Program Tool Compatibility Table

The availability of steps, monitors and restrictions depends on the license installed on the controller.

The table below shows which steps, monitors and restrictions are available for the various tools.

Supported Tools

ES

ST

STR

IXB

SR

SL (Low Voltage)

BCV-RE/BCP-RE

MWR

STB

QST

STW

External Tool

PF6000-Handheld

X

X

X

-

X

X

X

X

X

X

X

X

PF6000-StepSync

-

X

X

-

X

X

-

-

-

X

-

-

PF6000-Fixtured

-

-

-

-

-

-

-

-

-

X

-

-

Step Type

ES

ST

STR

IXB

SR

SL (Low Voltage)

BCV-RE/BCP-RE

MWR

STB

QST

STW

External Tool

Tighten to Angle

X

X

X

X

X

X

-

-

X

X

-

-

Tighten to Torque

X

X

X

X

X

X

-

-

X

X

-

-

Tighten to Trigger Release

X

X

X

X

X

X

-

-

X*

-

-

-

Tighten to Torque + Angle

X

X

X

X

X

X

-

-

X

X

-

-

Tighten to Torque AND Angle

X

X

X

X

X

X

-

-

X

X

-

-

Tighten to DynaTork

X

X

X

X

X

X

-

-

X

X

-

-

Wait

X

X

X

X

X

X

-

-

X

X

-

-

Socket Release

X

X

X

X

X

X

-

-

X

X

-

-

Run until Digital Input

X

X

X

-

X

X

-

-

-

X

-

-

Tighten to Torque or Angle

X

X

X

X

X

X

-

-

X

X

-

-

Loosen to Angle

X

X

X

X

X

X

-

-

X

X

-

-

Loosen to Torque

X

X

X

X

X

X

-

-

X

X

-

-

Loosen to Trigger Release

X

X

X

X

X

X

-

-

X*

-

-

-

Thread Cutting to Torque

X

X

X

X

X

X

-

-

X

X

-

-

Synchronization Point

-

-

-

-

-

-

-

-

-

X##

-

-

Engage

X

X

X

X

X

X

-

-

-

X

-

-

Rundown

X

X

X

X

X

X

-

-

-

X

-

-

Tighten to Yield

X

X

X

X

X

X

-

-

-

X

-

-

Tighten to Yield M2

-

-

-

-

-

-

-

-

-

X

-

-

External Result

X

X

X

-

X

X

X

-

X

X**

-

X

Clutch

-

-

-

-

-

-

X

-

-

-

-

-

Clutch Loosen

-

-

-

-

-

-

X

-

-

-

-

-

Mechatronic Wrench (MWR)

-

-

-

-

-

-

-

X

-

-

-

-

Torque Calibration

-

-

-

-

-

-

-

-

-

X#

-

-

Wrench Production

-

-

-

-

-

-

-

-

-

-

X

-

Wrench Quality

-

-

-

-

-

-

-

-

-

-

X

-

Monitors
(Evaluated at End of Step)

ES

ST

STR

IXB

SR

SL (Low voltage)

BCV-RE/BCP-RE

MWR

STB

QST

STW

External Tool

Time

X

X

X

X

X

X

-

-

X

X

-

-

Angle

X

X

X

X

X

X

-

X

X

X

X

-

Peak Torque

X

X

X

X

X

X

-

X

X

X

X

-

Shut Off Torque

X

X

X

X

X

X

-

-

X

X

-

-

Torque Rate Deviation

X

X

X

X

X

X

-

-

-

X

-

-

Post Thread Cut Angle

X

X

X

X

X

X

-

-

X

X

-

-

Post Thread Cut Peak Torque

X

X

X

X

X

X

-

-

X

X

-

-

Torque in Angle Window

X

X

X

X

X

X

-

-

X

X

-

-

Post View Torque High

X

X

X

X

X

X

-

-

X

X

-

-

Post View Torque Low

X

X

X

X

X

X

-

-

X

X

-

-

Angle from Yield

X

X

X

X

X

X

-

-

-

X

-

-

Stick-Slip detection

X

X

X

X

X

X

-

-

-

X

-

-

Prevailing Torque

X

X

X

X

X

X

-

-

X

X

-

-

Shut Off Current

X

X

X

X

X

X

-

-

X

X

-

-

Click

-

-

-

-

-

-

-

X

-

-

-

-

Torque Calibration

-

-

-

-

-

-

-

-

-

X#

-

-

Loosening Detection

-

-

-

-

-

-

-

-

-

-

X

-

Restrictions (Immediate Stop)

ES

ST

STR

IXB

SR

SL (Low voltage)

BCV-RE/BCP-RE

MWR

STB

QST

STW

External Tool

Maximum Torque

X

X

X

X

X

X

-

-

X

X

-

-

Maximum Angle

X

X

X

X

X

X

-

-

X

X

-

-

Maximum Time

X

X

X

X

X

X

-

-

X

X

-

-

Cross Thread

X

X

X

X

X

X

-

-

X

X

-

-

Torque Gradient

X

X

X

X

X

X

-

-

-

X

-

-

Rescinding Torque - Torque control process

X

X

X

X

X

X

-

-

X

X

-

-

Rescinding Torque - Angle control process

X

X

X

X

X

X

-

-

-

X

-

-

Torque Vs Current Deviation

X

X

X

X

X

X

-

-

-

X

-

-

Torque in Angle Window

X

X

X

X

X

X

-

-

X

X

-

-

Rehit

X

X

X

X

X

X

-

-

X

X###

-

-

Program Monitor Type
(Evaluate at end of program)

ES

ST

STR

IXB

SR

SL (Low voltage)

BCV-RE/BCP-RE

MWR

STB

QST

STW

External Tool

Program Monitor Angle

X

X

X

X

X

X

-

-

X

X***

-

-

Program Restriction Type
(Immediate Stop)

ES

ST

STR

IXB

SR

SL (Low voltage)

BCX

MWR

STB

QST

STW

External Tool

Program Restriction Torque High

X

X

X

X

X

X

-

X

X

X

X

-

Program Restriction Time High

X

X

X

X

X

X

-

X

X

X

-

-

* The STB tool shall only allow loosen to trigger/tighten to trigger release step in a multistep loosening/tightening program.

** External result is not supported in a PF6000-Fixtured/StepSync system.

*** Program Monitor Angle is not supported in a PF6000-Fixtured/StepSync system.

# Only supported by PF6000-Fixtured systems.

## Only supported by PF6000-Fixtured and PF6000-StepSync systems.

###　Not supported by PF6000-Fixtured systems.