Product Information

• General Information
  • Safety Signal Words
  • Warranty
  • Website
  • ServAid
  • Safety Data Sheets MSDS/SDS
  • Product Safety Video for Nutrunners
  • Country of Origin
  • Dimensional Drawings
• Overview
  • Technical Product Data
• Service Overview
  • Service Recommendations

General Information

WARNING

Risk of Property Damage or Severe Injury

Ensure that you read, understand and follow all instructions before operating the tool. Failure to follow all the instructions may result in electric shock, fire, property damage and/or severe bodily injury.

• Read all Safety Information delivered together with the different parts of the system.

• Read all Product Instructions for installation, operation and maintenance of the different parts of the system.

• Read all locally legislated safety regulations regarding the system and parts thereof.

• Save all Safety Information and instructions for future reference.

Safety Signal Words

Warranty

• Product warranty will expire 12+1 months after dispatch from Atlas Copco's Distribution Center.

• Normal wear and tear on parts is not included within the warranty.

  • Normal wear and tear is that which requires a part change or other adjustment/overhaul during standard tools maintenance typical for that period (expressed in time, operation hours or otherwise).

• The product warranty relies on the correct use, maintenance, and repair of the tool and its component parts.

• Damage to parts that occurs as a result of inadequate maintenance or performed by parties other than Atlas Copco or their Certified Service Partners during the warranty period is not covered by the warranty.

• To avoid damage or destruction of tool parts, service the tool according to the recommended maintenance schedules and follow the correct instructions.

• Warranty repairs are only performed in Atlas Copco workshops or by Certified Service Partners.

Atlas Copco offers extended warranty and state of the art preventive maintenance through its ToolCover contracts. For further information contact your local Service representative.

For electrical motors:

• Warranty will only apply when the electric motor has not been opened.

Website

Information concerning our Products, Accessories, Spare Parts and Published Matters can be found on the Atlas Copco website.

Please visit: www.atlascopco.com.

ServAid

ServAid is a portal that is continuously updated and contains Technical Information, such as:

• Regulatory and Safety Information

• Technical Data

• Installation, Operation and Service Instructions

• Spare Parts Lists

• Accessories

• Dimensional Drawings

Please visit: https://servaid.atlascopco.com.

For further Technical Information, please contact your local Atlas Copco representative.

Safety Data Sheets MSDS/SDS

The Safety Data Sheets describe the chemical products sold by Atlas Copco.

Please consult the Atlas Copco website for more information www.atlascopco.com/sds.

Product Safety Video for Nutrunners

Learn more about safety features on Atlas Copco nutrunners and what measures the operator has to take for a safe operation. Click the link or scan the QR code below to view the video:

https://www.youtube.com/watch?v=FAh6yttvUpw

Country of Origin

For the Country of Origin, please refer to the information on the product label.

Dimensional Drawings

Dimensional Drawings can be found either in the Dimensional Drawings Archive, or on ServAid.

Please visit: http://webbox.atlascopco.com/webbox/dimdrw or https://servaid.atlascopco.com.

Overview

• Technical Product Data

Technical Product Data

Technical Product Data can be found on either ServAid, or the Atlas Copco website.

Please visit: https://servaid.atlascopco.com or www.atlascopco.com.

Service Overview

• Service Recommendations

Service Recommendations

Preventive maintenance is recommended at regular intervals. See the detailed information on preventive maintenance. If the product is not working properly, take it out of service and inspect it.

If no detailed information about preventive maintenance is included, follow these general guidelines:

• Clean appropriate parts accurately

• Replace any defective or worn parts

Installation

• Installation Requirements
  • Installation
• Installation Instructions
  • Wireless Communication
  • Attaching and Removing the Battery

Installation Requirements

• Installation

Installation

For installation guideline, see Power Focus 6000 user guide.

Installation Instructions

• Wireless Communication
• Attaching and Removing the Battery

Wireless Communication

This tool supports both WLAN 2.4 and 5 GHz (except AdHoc), as well as Bluetooth.

Multitool Bluetooth connection may cause connection interference and is not recommended. The configuration of WLAN and Bluetooth is handled in Tools Talk Service 2.

Attaching and Removing the Battery

Operation

• Ergonomic Guidelines
• Operating Instructions
  • LED Indicator (HMI)
  • Tightening

Ergonomic Guidelines

Consider your workstation as you read through this list of general ergonomic guidelines to identify areas for improvement in posture, component placement, or work environment.

• Take frequent breaks and change work positions frequently.

• Adapt the workstation area to your needs and the work task.

  • Adjust for a convenient reach range by determining where parts and tools need to be located to avoid static load.

  • Use workstation equipment such as tables and chairs appropriate for the work task.

• Avoid work positions above shoulder level or with static holding during assembly operations.

  • When working above shoulder level, reduce the load on the static muscles by lowering the weight of the tool, using for example torque arms, hose reels or weight balancers. You can also reduce the load on the static muscles by holding the tool close to the body.

  • Take frequent breaks.

  • Avoid extreme arm or wrist postures, particularly during operations requiring a degree of force.

• Adjust for a convenient field of vision that requires minimal eye and head movements.

• Use appropriate lighting for the work task.

• Select the appropriate tool for the work task.

• In noisy environments, use ear protection equipment.

• Use high-quality inserted tools and consumables to minimize exposure to excessive levels of vibration.

• Minimize exposure to reaction forces.

  • When cutting:

    A cut-off wheel can get stuck if the cut-off wheel is bent or not guided properly. Use the correct flange for the cut-off wheel and avoid bending the cut-off wheel during operation.

  • When drilling:

    The drill might stall when the drill bit breaks through. Use support handles if the stall torque is high. The safety standard ISO11148 part 3 recommends using a device to absorb a reaction torque above 10 Nm for pistol grip tools and 4 Nm for straight tools.

  • When using direct-driven screwdrivers or nutrunners:

    Reaction forces depend on the tool settings and joint characteristics. Strength and posture determine the amount of reaction force that an operator can tolerate. Adapt the torque setting to the operator's strength and posture and use a torque arm or reaction bar if the torque is too high.

• In dusty environments, use a dust extraction system or wear a mouth protection mask.

Operating Instructions

• LED Indicator (HMI)
• Tightening

LED Indicator (HMI)

Tightening

As tightening torque increase the reaction force build up equally. Make sure that the tool is in correct working order and that the controller is correctly programmed. By doing this you avoid unexpected behavior from the tool, which may result in operator injury.

Rotation Direction for the Tightening

Check that the tool is in the correct running direction by turning the reverse button or reverse ring :

Pistol Grip Models (with side buttons)

• Press in the reverse switch on the right hand side of the tool, to set the direction clockwise (CW).

• Press in the reverse switch on the left hand side of the tool, to set the direction counter clockwise (CCW).

Pistol Grip Models (without side buttons)

• Double press the function button on the top of the start trigger to shift the direction between clockwise (CW) and counter clockwise (CCW).

Angle Models

• Turn the reverse ring to the right, to set the direction clockwise (CW).

• Turn the reverse ring to the left, to set the direction counter clockwise (CCW).

Soft Start

The soft start function facilitates the screwhead and thread to reach the snug level. The duration of the soft start is adjustable.

For further information about tightening, see Power Focus 6000 Configuration manual.

Service

• Preventing ESD Problems
• Maintenance Instructions
  • Service Recommendations
  • Preventive Maintenance
    • Maximizing Battery Life
  • Overhaul
• Lubrication Instructions
  • Lubricating Guide
  • Lubrication

Preventing ESD Problems

The components inside the product and controller are sensitive to electrostatic discharge. To avoid future malfunction, make sure that service and maintenance is carried out in an ESD approved work environment. The figure below shows an example of an appropriate service work station.

Maintenance Instructions

• Service Recommendations
• Preventive Maintenance
  • Maximizing Battery Life
• Overhaul

Service Recommendations

Preventive maintenance is recommended at regular intervals. See the detailed information on preventive maintenance. If the product is not working properly, take it out of service and inspect it.

If no detailed information about preventive maintenance is included, follow these general guidelines:

• Clean appropriate parts accurately

• Replace any defective or worn parts

Preventive Maintenance

• Maximizing Battery Life

Maximizing Battery Life

Do not leave the battery connected to the tool if you do not use the tool for several days. The battery can discharge and go into “sleep mode” which will require a special wake-up charge procedure. For further information, see instructions for multicharger, 4211542485.

Overhaul

Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Service must only be carried out by qualified personnel who have access to the Service instruction and/or have been trained for service on this tool.

The electric motor is a sealed unit and may under no circumstances be opened by anyone else than Atlas Copco Industrial Technique AB.

If it is judged that the electric motor is defect or in need of service, the complete motor unit should be returned to Atlas Copco Industrial Technique AB for exchange.

Motors which have been opened by anyone else than Atlas Copco Industrial Technique AB will not be serviced.

Overhaul and preventive maintenance is recommended at regular intervals once per year or after maximum 250.000 tightening depending on which occurs sooner. More frequent overhaul may be needed if the machine is used in heavy-duty operations. If the machine not is working properly, it should immediately be taken away for inspection.

The backup battery must be replaced within 24 months from the tool's production date, or last battery backup replacement. Shorter interval if tool has been used in the higher accepted temperature range. A replaced backup battery should be recycled according to the Recycling Instruction. Spare backup batteries must not be stored in ambient temperatures above 30⁰C and should due to self-discharge not be stored more than 6 months before powering it up for 4 hours. Spare backup batteries can be stored in a fridge (non-condensing environment).

When dismantling the tool always use the specially designed service tool 4080 0848 80, (two service tools are required).

Lubrication Instructions

• Lubricating Guide
• Lubrication

Lubricating Guide

Lubrication

Lubricate gears and clutch with grease containing molybdenum disulphide (e.g. Molykote BR2 Plus). Lubricate o-rings and threaded connections with grease before assembling.

For more information, see Spare Parts section in ServAid - https://servaid.atlascopco.com.

Troubleshooting

• Overheated Tool

Overheated Tool

The tool can handle any normal line jobs that an operator sustains with the proper adjustments.

The tool temperature can be influenced by the following parameters:

• short cycle time

• torque above rated

• too low speed

• very high prevailing torque

• very soft joints

• ambient temperature

Recycling

• Environmental Regulations
• Recycling Instruction

Environmental Regulations

When a product has served its purpose it has to be recycled properly. Dismantle the product and recycle the components in accordance with local legislation.

Batteries shall be taken care of by your national battery recovery organization.

Recycling Instruction