Product Information

• General Information
  • Safety Signal Words
  • Warranty
  • Website
  • ServAid
  • Safety Data Sheets MSDS/SDS
  • Special Precaution
    • Warning
  • Country of Origin
  • Dimensional Drawings
• Overview
  • AutoTrim Valve Overview
  • Technical Product Data

General Information

WARNING

Risk of Property Damage or Severe Injury

Ensure that you read, understand and follow all instructions before operating the tool. Failure to follow all the instructions may result in electric shock, fire, property damage and/or severe bodily injury.

• Read all Safety Information delivered together with the different parts of the system.

• Read all Product Instructions for installation, operation and maintenance of the different parts of the system.

• Read all locally legislated safety regulations regarding the system and parts thereof.

• Save all Safety Information and instructions for future reference.

Safety Signal Words

Warranty

• Product warranty will expire 12+1 months after dispatch from Atlas Copco's Distribution Center.

• Normal wear and tear on parts is not included within the warranty.

  • Normal wear and tear is that which requires a part change or other adjustment/overhaul during standard tools maintenance typical for that period (expressed in time, operation hours or otherwise).

• The product warranty relies on the correct use, maintenance, and repair of the tool and its component parts.

• Damage to parts that occurs as a result of inadequate maintenance or performed by parties other than Atlas Copco or their Certified Service Partners during the warranty period is not covered by the warranty.

• To avoid damage or destruction of tool parts, service the tool according to the recommended maintenance schedules and follow the correct instructions.

• Warranty repairs are only performed in Atlas Copco workshops or by Certified Service Partners.

Atlas Copco offers extended warranty and state of the art preventive maintenance through its ToolCover contracts. For further information contact your local Service representative.

For electrical motors:

• Warranty will only apply when the electric motor has not been opened.

Website

Information concerning our Products, Accessories, Spare Parts and Published Matters can be found on the Atlas Copco website.

Please visit: www.atlascopco.com.

ServAid

ServAid is a portal that is continuously updated and contains Technical Information, such as:

• Regulatory and Safety Information

• Technical Data

• Installation, Operation and Service Instructions

• Spare Parts Lists

• Accessories

• Dimensional Drawings

Please visit: https://servaid.atlascopco.com.

For further Technical Information, please contact your local Atlas Copco representative.

Safety Data Sheets MSDS/SDS

The Safety Data Sheets describe the chemical products sold by Atlas Copco.

Please consult the Atlas Copco website for more information www.atlascopco.com/sds.

Special Precaution

• Check that the power socket is properly fastened.

• Replace the square drive retainer or socket if worn.

• Avoid unnecessary idling.

• When using a suspension yoke, make sure that it is in good condition and correctly fastened.

Warning

WARNING

Polymer hazard

The vanes in this product contain PTFE (a synthetic fluoropolymer). Due to wear, there might be PTFE particles inside the product. Heated PTFE can produce fumes which may cause polymer fume fever with flu-like symptoms, especially when smoking contaminated tobacco.

Health and Safety recommendations for PTFE must be followed when handling vanes and other components:

• Do not smoke when servicing this product

• PTFE-particles must not come in contact with open fire, glow or heat

• Motor components must be washed with cleaning fluid and not blown clear with an air line

• Wash your hands before starting any other activity

Country of Origin

For the Country of Origin, please refer to the information on the product label.

Dimensional Drawings

Dimensional Drawings can be found either in the Dimensional Drawings Archive, or on ServAid.

Please visit: http://webbox.atlascopco.com/webbox/dimdrw or https://servaid.atlascopco.com.

Overview

• AutoTrim Valve Overview
• Technical Product Data

AutoTrim Valve Overview

This tool is equipped with an AutoTrim valve, which gives the tool optimal performance on mixed hard and soft joints. (For applications where the tool is used for tightening joints with similar characteristics, Trim Valve can be used.)

The AutoTrim valve is factory preset to suit a majority of applications. It gives a reduced speed during rundown. After 1-2 pulses it shifts automatically to full speed/power for the rest of the tightening. Regularly check the correct operation of the AutoTrim valve. Non-switching (from restricted to open operation) will cause longer tightening time with risk of over-tightening of the joint. Premature switching to open position (i.e. when tool is running free) might cause erratic shut-off due to too few pulses.

The AutoTrim valve gives a reduced speed during rundown. After 1-2 pulses on a joint it shifts automatically to full speed/power for the rest of the tightening, as shown in illustration below.

Possible adjustments:

• Free speed (factory set to approx 70% of full speed). See Adjusting the Free Speed.

• Switch point from reduced to full power (factory set to 1-2 pulses) for standard, non reporting (RE) applications. See Adjusting the Switch Point.

• Power during pulsing (factory set to full power). See Adjusting the Pulsing Power.

In most cases the factory settings give the best performance.

Technical Product Data

Technical Product Data can be found on either ServAid, or the Atlas Copco website.

Please visit: https://servaid.atlascopco.com or www.atlascopco.com.

Installation

• Installation Requirements
  • Air Quality
  • Air Lubrication Guide
  • Compressed Air Connection
  • Air Pressure Regulation
• Installation Instructions
  • Installation of Vibrating Tools

Installation Requirements

• Air Quality
• Air Lubrication Guide
• Compressed Air Connection
• Air Pressure Regulation

Air Quality

• For optimum performance and maximum product life we recommend the use of compressed air with a maximum dew point of +10°C (50°F). We also recommend to install an Atlas Copco refrigeration type air dryer.

• Use a separate air filter which removes solid particles larger than 30 microns and more than 90% of liquid water. Install the filter as close as possible to the product and prior to any other air preparation units to avoid pressure drop.

For impulse/impact tools make sure to use lubricators adjusted for these tools. Regular lubricators will add too much oil and therefore decrease the tool performance due to too much oil in the motor.

Make sure that the hose and couplings are clean and free from dust before connecting to the tool.

Both lubricated and lubrication free products will benefit from a small quantity of oil supplied from a lubricator.

Air Lubrication Guide

Recommended air lubricators:

• Atlas Copco Optimizer (1 liter) 9090 0000 04

• Q8 Chopin 46

• Shell Air Tool Oil S2 A 320

Compressed Air Connection

WARNING

Risk of severe injury

Air under pressure can cause injury.

• Always shut off the air supply when not in use or before any adjustments.

• Drain the hose of air pressure and disconnect the tool from air supply when not in use or before any adjustments.

• Always use the correct hose size and air pressure for the tool.

WARNING

Compressed Air

High air pressure can cause severe damage and bodily injury.

• Do not exceed maximum air pressure.

• Make sure that there are no damaged or loose hoses or fittings.

For correct air pressure and hose size, see the Technical Product Data on - https://servaid.atlascopco.com or www.atlascopco.com.

Make sure that the hose and couplings are clean and free from dust before connecting to the tool.

Air Pressure Regulation

Make sure to adjust the regulator to the lowest expected pressure on the line.

Adjusting the air pressure will have the following consequences:

• Decreasing the air pressure will result in a slower but more accurate tool.

• Increasing the air pressure will result in a faster but less accurate tool.

If the pressure from the airline is below five bar, a tool from the EP L-series (designed for low pressure installations) is recommended.

Installation Instructions

• Installation of Vibrating Tools

Installation of Vibrating Tools

We recommend using a minimum length of 300 mm (12") of flexible hose for compressed air between a vibrating tool and the quick coupling.

Operation

• Ergonomic Guidelines
• Operating Instructions
  • Length of "L" and "N" Depending on Model
  • Optimizing the Tool Performance
  • Adjusting the Switch Point
  • Adjusting the Pulsing Power
  • Setting of tightening torque with AutoTrim Valve (AT)
  • Controlling the Function Using Speed Change
  • Adjusting the Free Speed
  • Operating Instructions
  • Setting of Tightening Torque

Ergonomic Guidelines

Consider your workstation as you read through this list of general ergonomic guidelines and see if you can identify areas for improvement in posture, component placement, or work environment.

• Take frequent breaks and change work positions frequently.

• Adapt the work area to your needs and the work task.

  • Adjust for convenient reach range by determining where parts or tools should be located to avoid static load.

  • Use workstation equipment such as tables and chairs appropriate for the work task.

• Avoid work positions above shoulder level or with static holding during assembly operations.

  • When working above shoulder level, reduce the load on the static muscles by reducing the weight of the load. You can also reduce the load on the static muscles by holding the load close to the body.

  • Make sure to take frequent breaks.

  • Avoid extreme arm or wrist postures, particularly for operations requiring a degree of force.

• Adjust for convenient field of vision by minimizing movement of the eyes and head during the work task.

• Use the appropriate lighting for the work task.

• Use ear protection equipment in noisy environments.

• Use dust extraction system or mouth protection mask in dusty environments.

Operating Instructions

• Length of "L" and "N" Depending on Model
• Optimizing the Tool Performance
• Adjusting the Switch Point
• Adjusting the Pulsing Power
• Setting of tightening torque with AutoTrim Valve (AT)
• Controlling the Function Using Speed Change
• Adjusting the Free Speed
• Operating Instructions
• Setting of Tightening Torque

Length of "L" and "N" Depending on Model

Optimizing the Tool Performance

Recommended number of pulses

A Pulse tool well suited for your application should reach the target torque (with shut off) within 5-20 pulses. The number of pulses it takes for the tool to reach target torque can be measured with an analyzer. The tightening time can also be used as a guide, to know if the tool is appropriate for your application:

• ≤ 1 second for tools up to 30 Nm

• ≈ 1 second for tools up to 80 Nm

• ≈ 2 seconds for tools up to 150 Nm

• ≈ 5 seconds for tools up to 450 Nm

• ≤ 10 seconds for tools up to 850 Nm

If the target torque is achieved with less than 5 pulses (= short tightening time), the torque scatter will increase and it can be difficult to adjust to the right level, especially on hard joints.

If the target torque is achieved with more than 20 pulses (= too long tightening time) the wear will increase and more frequent oil filling and service will be required. Too long tightening time, in combination with high production rate, may also result in excessive heating of the oil. In that case the power will decrease with longer tightening time and sometimes no shut off.

If the target torque is achieved with less than 5 pulses this can be fixed by:

• Decreasing the air pressure.

• Reducing the speed by means of the AutoTrim or Trim valve.

• If the above is not possible or does not give wanted results, a smaller tool may be a better choice.

If the target torque is achieved with more than 20 pulses this can be fixed by:

• Increasing the dynamic air pressure to 6-7 bar for standard EP tools, or up to 5 bar for low pressure EP L-tools.

• Adjust the AutoTrim or Trim valve to give maximum power/speed.

• If the above is not possible or does not give wanted results, a bigger tool may be a better choice.

When changing the air pressure, the target torque must be measured again and adjusted if needed.

Adjusting the Switch Point

• Remove the cover (1) with 22 mm wrench while holding the valve casing with hook wrench.

• Adjust the valve (2) with 1.5 mm Allen key supplied with AutoTrim valve. From fully closed (+) position to normal operation the needle valve is opened between 6 and 8 turns (-) depending on tool size.

• Restore cover (1).

• Perform a function control.

If the valve is too much closed, the AutoTrim valve will not shift to open position when pulsing starts. If the valve is too much open, the AutoTrim will directly open to full speed and power.

Clockwise (+) rotation delays the switch point (closes the needle valve) and vice versa.

If the tool is used for reporting applications (RE) the needle valve has to be turned more open (-) to compensate for the air volume in the signal hose.

Adjusting the Pulsing Power

The AutoTrim valve is factory set to full pulsing power, that is, the length of N is set according to the table.

To improve accuracy (more pulses before shut off) on hard or medium hard joints, reduce the power. The power is reduced by turning the nut (1) clockwise (increased lenght of N).

Setting of tightening torque with AutoTrim Valve (AT)

Controlling the Function Using Speed Change

Make sure that any socket is firmly attached. The tool should run at reduced speed.

Run the tool in the air (A).

With the reversing knob in reversing direction, pull the trigger and (with trigger still pressed) quickly pull the reversing knob to forward direction. (B) The AutoTrim valve should then switch from reduced to full speed. If the tool is running with full speed at (A) or still remaining at reduced speed at (B) the AutoTrim valve is in need of adjustment or service, see Adjusting the Switch Point.

Adjusting the Free Speed

The AutoTrim valve is factory set to approximately 70% of full speed. To reduce the free speed, reduce the length of L. To increase the free speed, increase the length of L.

Adjust the length of L by turning the support ring (1).

On very hard joints (<30°) at low torque levels, further speed reduction might be necessary. When the tool is used only on soft joints, less or no speed reduction is needed.

The factory set length of L is depending on the tool size, see table.

Operating Instructions

Setting of Tightening Torque

The adjusting screw (the slotted screw) is the only screw that initially should be adjusted. Start at a low torque adjustment and gradually increase the setting until you reach the desired torque level. See detailed illustrations for setting of the tightening torque when using AutoTrim function and Trim function respectively.

Using the tool at a higher torque, than recommended maximum torque, might result in improper function and faster wear.

Always check the setting on your actual joint.

Service

• Maintenance Instructions
  • Servicing the AutoTrim Valve
  • Service tools
  • Preventive Maintenance
• Lubrication Instructions
  • Rust Protection and Cleaning
  • Grease Guide ErgoPulse
  • Lubrication Guide
  • Inspection and Lubrication of the Pulse Unit
  • Recommended Oil for the Pulse Unit
  • Filling the Pulse Unit with Oil
    • Method 1 (using an ST Analyzer and a Transducer)
    • Method 2 (without ST Analyzer and Transducer)
  • Refill the Pulse-Unit with Oil
• Dismantling/Assembling Instructions
  • Tightening of Threaded Connections
• Dynamic measurement
• Static measuring with fixed transducers
  • Test equipment and performance
  • Test conditions
• Test Method - Static or Dynamic
• Static measurement (Recommended)

Maintenance Instructions

• Servicing the AutoTrim Valve
• Service tools
• Preventive Maintenance

Servicing the AutoTrim Valve

Make sure all parts are clean. O-rings should be lightly greased. Valve and bracket should be sparsely oiled with light oil. Make sure that the valve moves easily on the bracket. When adjusting the throttle valve, start from fully closed position (clockwise) and open between 6-8 turns. Check and adjust again if needed.

Check and adjust the lengths of L and N corresponding to the ordering number of the AutoTrim valve (as of 2008 the ordering number is engraved on the AutoTrim casing). See Adjusting the Free Speed and Adjusting the Pulsing Power.

Test the valve function on the corresponding EP tool. Change the filter regularly to prevent clogging, decreased power, and incorrect function.

Service tools

Atlas Copco Service tools are designed to make assembly and disassembly fast and easy with less risk of damaging parts in the process.

When assembling the tool after service it is important to tighten the parts correctly to:

• Optimize performance of the tool.

• Minimize the risk of parts coming loose during operation.

You can find information about service tools and tightening data in the Spare part list on ServAid.

Preventive Maintenance

Preventive maintenance is recommended once per year or after a maximum of 250.000 tightenings. A complete overhaul include:

• Clean the pulse unit and change worn or damaged parts.

• Clean the air motor and change worn or damaged parts.

• Clean the silencer and the strainer of the inlet adapter, change the filter and change worn or damaged parts.

• Clean the trigger and reversing valve and change worn or damaged parts.

Do not change the o-rings in the pulse unit except at the regular overhaul once per year or after a maximum of 250.000 tightening.

Lubrication Instructions

• Rust Protection and Cleaning
• Grease Guide ErgoPulse
• Lubrication Guide
• Inspection and Lubrication of the Pulse Unit
• Recommended Oil for the Pulse Unit
• Filling the Pulse Unit with Oil
  • Method 1 (using an ST Analyzer and a Transducer)
  • Method 2 (without ST Analyzer and Transducer)
• Refill the Pulse-Unit with Oil

Rust Protection and Cleaning

Water in the compressed air can cause rust. To prevent rust we strongly recommend to install an air dryer.

Water and particles can cause sticking of vanes and valves. This can be prevented by installing an air filter close to the product to avoid pressure drop.

Before longer stand stills always protect your tool by adding a few drops of oil into the air inlet. Run the tool for 5–10 seconds and absorb any access oil at the air outlet in a cloth.

Grease Guide ErgoPulse

Lubrication Guide

Inspection and Lubrication of the Pulse Unit

Recommended Oil for the Pulse Unit

The recommended oil for the pulse unit is Atlas Copco Pulse Unit Oil.

A bottle of Atlas Copco Pulse Unit Oil and the required syringe or syringes are orderable as kits. Please see Service Kits for ordering numbers.

Filling the Pulse Unit with Oil

There are different methods to fill the pulse unit with oil, depending on available equipment:

• Using an ST Analyzer and a Transducer. Follow the instructions in Method 1.
  This method is the fastest. It will give an optimized tool performance and result in the longest filling intervals.

• Without an ST Analyzer and a Transducer. Follow the instructions in Method 2.
  This method is not as fast and accurate as using Method 1.

Method 1 (using an ST Analyzer and a Transducer)

Method 2 (without ST Analyzer and Transducer)

Refill the Pulse-Unit with Oil

For optimum machine performance the pulse unit must be correctly filled with oil. Due to a possible microleakage of oil from the pulse unit, it could be necessary to refill the unit between the regular overhaul intervals. The frequency of this procedure depends on the type of application, number of cycles, tightening time etc. An accurate refill of the pulse unit gives long service intervals.

Too much oil in the pulse unit implies a low pulse frequency and slow tightening.

Too little oil in the pulse unit implies a high pulse frequency and there will be a risk of a decreasing tightening torque. In particular at the first tightening after a break the machine might race.

Use Atlas Copco Pulse Unit Oil.

Running the machine with too little oil may damage the pulse unit.

After the refill – Check the tightening torque.

Steps

Fill the pulse unit with oil according to steps No. 1-3 seen in the picture, after the disassembly of the pulse unit. Run the machine in a vice for 10 seconds according to step No. 4. Complete the rest of the steps. For best performance use Atlas Copco Pulse Unit Oil.

A bottle of Atlas Copco Pulse Unit Oil and the required syringe or syringes are orderable as a kit. See Service Kits for ordering numbers.

Low oil level

How to detect a low oil level in the pulse unit:

• Longer tightening time

• Very high pulse frequency, especially when the tool has not been used for a while.

• Low torque or abnormal torque changes (increased scatter).

• No shut off

To measure the pulse frequency use a static torque transducer or an inline transducer connected to torque testing equipment, se Testing/Measuring section.

Dismantling/Assembling Instructions

• Tightening of Threaded Connections

Tightening of Threaded Connections

The tightening torque indicated in the exploded views (see Spare parts section in https://servaid.atlascopco.com) will give the right clamping force and prevent parts from loosening. It is important not to exceed the clamping force, these parts must be able to open up without being damaged at service. After some time of operation and in special circumstances, depending on application and usage, the parts may however loosen somewhat. The tightening torque can then be increased by 10-20% and some type of low or medium thread locking fluid can be applied.

Dynamic measurement

Always verify the setting on your actual joint.

Always verify the dynamic measurement on your actual joint by a static check with a torque wrench (electronic).

Static measuring with fixed transducers

Test equipment and performance

Equipment:

• Tachometer.

• STanalyser.

• SRTT transducer (secure the transducer firmly).

1. Test the free speed in the forward direction with the tachometer.

   For AutoTrim versions make sure that the unreduced speed is measured (refer to section Function control - AutoTrim in the Trouble shooting schedule chapter of the service instruction for details).

   Test the AutoTrim function.

2. Test the max torque and pulse frequency.

   Set the filter frequency in STanalyser to 850 Hz.

   Measure the torque and pulse frequency in the reverse direction. Use a tightening time of approximately 1 second.

3. Check of shut-off mechanism.

   Run the tool in the forward direction. If the shut-off mechanism is working properly the tool shuts off.

Test conditions

Temperature pulse unit: approx. 20° C.

Air pressure: 6,3 bar (90psi) dynamic

Hose size: 8 mm Hose length: 3 m

The tool should achieve the following values after maintenance:

Correct pulse frequency indicates that the air motor and the pulse unit are in good condition. If the pulse pulse frequency is to high - fill oil. If the pulse frequency is too low - reduce oil.

Test Method - Static or Dynamic

A static torque measurement is recommended for the ErgoPulse machines.

If dynamic torque measurement with an electronic inline torque transducer is used, always verify your measurement result by a static check with a torque wrench (electronic).

For more information, refer to Atlas Copco "Pocket Guide to Pulse Tools". Ordering No. 9833 1225 01.

Static measurement (Recommended)

Recycling

• Environmental Regulations
• Recycling Instructions

Environmental Regulations

When a product has served its purpose it has to be recycled properly. Dismantle the product and recycle the components in accordance with local legislation.

Batteries shall be taken care of by your national battery recovery organization.

Recycling Instructions