Technical Data

• Product Data
• Environmental Conditions
• Compatible tools

Product Data

Environmental Conditions

Compatible tools

Declarations

• Liability
• EU DECLARATION OF CONFORMITY
• UK DECLARATION OF CONFORMITY
• WEEE
• FCC and ISED Compliance Statement
• Regional Requirements

Liability

Many events in the operating environment may affect the tightening process and shall require a validation of results. In compliance with applicable standards and/or regulations, we hereby require you to check the installed torque and rotational direction after any event that can influence the tightening result. Examples of such events include but are not limited to:

• initial installation of the tooling system

• change of part batch, bolt, screw batch, tool, software, configuration or environment

• change of air- or electrical connections

• change in line ergonomics, process, quality procedures or practices

• changing of operator

• any other change that influences the result of the tightening process

The check should:

• Ensure that the joint conditions have not changed due to events of influence.

• Be done after initial installation, maintenance or repair of the equipment.

• Occur at least once per shift or at another suitable frequency.

EU DECLARATION OF CONFORMITY

We, Atlas Copco Industrial Technique AB, SE-105 23 STOCKHOLM SWEDEN, declare under our sole responsibility that the product (with name, type and serial number, see front page) is in conformity with the following Directive(s):
2011/65/EU (RoHS), 2014/30/EU (EMC), 2015/863/EU (RoHS amendment)

Harmonized standards applied:
EN IEC 61000-6-2:2019; EN IEC 61000IEC 61000-6-3:2020-6-3:2021; IEC 61000-6-2:2016; IEC 61000-6-3:2020

Authorities can request relevant technical information from:
Product Compliance Manager, Atlas Copco Industrial Technique AB, SE-105 23 Stockholm Sweden

Stockholm, 31 January 2025

Lars Eklöf, Managing Director

Signature of issuer

UK DECLARATION OF CONFORMITY

We, Atlas Copco Industrial Technique AB, SE-105 23 STOCKHOLM SWEDEN, declare under our sole responsibility that the product (with name, type and serial number, see front page) is in conformity with the following UK Regulation(s): S.I. 2017/1206
Designated Standards applied: BS EN IEC 61000-6-2:2019; BS EN IEC 61000IEC 61000-6-3:2020-6-3:2021; BS IEC 61000-6-2:2016; BS IEC 61000-6-3:2020

Authorities can request relevant technical information from:
Product Compliance Manager, Atlas Copco Industrial Technique AB, SE-105 23 Stockholm Sweden

Stockholm, 31 January 2025

Lars Eklöf, Managing Director

Signature of issuer

WEEE

Information concerning Waste of Electrical and Electronic Equipment (WEEE):
This product and its information, meets the requirements of the WEEE directive/regulations (2012/19/EU), and must be handled in compliance with the directive/regulations.

The product is marked with the following symbol:

Products marked with a crossed-out wheeled bin symbol and a single black bar underneath, contain parts that must be handled in compliance with the WEEE directive/regulations. The entire product, or the WEEE parts, can be sent to your “Customer Center” for handling.

FCC and ISED Compliance Statement

This device complies with Part 15 of the FCC Rules. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this device.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The device is only in compliance if no changes or modifications are made to the device. The antenna is fixed to the device and no change in antenna or fixation of the antenna is acceptable and such modification is considered to violate the Compliance Statement.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

ISED Compliance Statement:

This device complies with: CAN ICES-1 (A)/NMB-1(A)

(English) This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device.

(French) Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:

1) l’appareil ne doit pas produire de brouillage;

2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Regional Requirements

WARNING

This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to

https://www.p65warnings.ca.gov/

Safety

WARNING

Read all safety warnings, instructions, illustrations and specifications provided with this power tool.

Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury.

Save all warnings and instructions for future reference.

WARNING

All locally legislated safety rules regarding installation, operation and maintenance shall be respected at all times.

Intended Use

This equipment is intended to be used with the products listed below.
No other use permitted.

Use only the following Atlas Copco Battery:

Product Specific Instructions

• Safety Information
• Operation
  • Operating the Wrench
• Service and Maintenance
  • Preventing ESD Problems
  • Cleaning

Safety Information

WARNING

Never try to recharge non-rechargeable batteries! Non-rechargeable batteries may leak when charging. They can explode and cause risk of fire and injuries.

WARNING

All locally legislated safety rules regarding installation, operation and maintenance shall be respected at all times.

For additional safety information consult:

• Other documents and information packed with this tool

• http://servaidweb.atlascopco.com

• Your employer, union and/or trade association

• http://www.osha.gov (USA)

• http://europe.osha.eu.int (Europe)

Operation

• Operating the Wrench

Operating the Wrench

Refer to the Product Instructions of MTRwrench POWER BANK ADAPTOR.

Service and Maintenance

• Preventing ESD Problems
• Cleaning

Preventing ESD Problems

The components inside the product and controller are sensitive to electrostatic discharge. To avoid future malfunction, make sure that service and maintenance is carried out in an ESD approved work environment. The figure below shows an example of an appropriate service work station.

Cleaning

Keep the MTRwrench POWER BANK ADAPTOR clean.

After use, remove any traces of oil and grease from the MTRwrench POWER BANK ADAPTOR with a soft cloth and a soft surface cleaner for oil/grease. Do not use aggressive or abrasive cleaner.

Use an anti-static cleaning cloth in order to remove dust from the MTRwrench POWER BANK ADAPTOR.

Avoid using harsh detergents to clean the MTRwrench POWER BANK ADAPTOR.

Clean the contact of the MTRwrench POWER BANK ADAPTOR by using an electrical contact cleaner solution.

Signs and Stickers

The product is fitted with signs and stickers containing important information about personal safety and product maintenance. The signs and stickers shall always be easy to read. New signs and stickers can be ordered by using the spare parts list.

Information on Environmental Labeling of Packaging

EU Decision 129/97/EC.

Useful Information

• ServAid

ServAid

ServAid is a portal that is continuously updated and contains Technical Information, such as:

• Regulatory and Safety Information

• Technical Data

• Installation, Operation and Service Instructions

• Spare Parts Lists

• Accessories

• Dimensional Drawings

Please visit: https://servaid.atlascopco.com.

For further Technical Information, please contact your local Atlas Copco representative.