Product Information

• General Information
  • Safety Signal Words
  • Warranty
  • Website
  • ServAid
  • Safety Data Sheets MSDS/SDS
  • Country of Origin
  • Dimensional Drawings
• Overview
  • Battery Overview
  • Ambient Temperature
  • Battery Charger Data

General Information

WARNING

Risk of Property Damage or Severe Injury

Ensure that you read, understand and follow all instructions before operating the tool. Failure to follow all the instructions may result in electric shock, fire, property damage and/or severe bodily injury.

• Read all Safety Information delivered together with the different parts of the system.

• Read all Product Instructions for installation, operation and maintenance of the different parts of the system.

• Read all locally legislated safety regulations regarding the system and parts thereof.

• Save all Safety Information and instructions for future reference.

Safety Signal Words

Warranty

The warranty period of the battery expires 12 months after the battery arrives at the customer, or after 500 charge cycles, whichever occurs first.

"Charge cycle" means any charge of the battery pack that increases the state of charge of the battery by more than 10%.

Normal wear and tear, and loss of performance due to normal wear of the cells is not included within the warranty.

Warranty does not apply if a battery has been abused, misused, opened, dismantled or modified.

Website

Information concerning our Products, Accessories, Spare Parts and Published Matters can be found on the Atlas Copco website.

Please visit: www.atlascopco.com.

ServAid

ServAid is a portal that is continuously updated and contains Technical Information, such as:

• Regulatory and Safety Information

• Technical Data

• Installation, Operation and Service Instructions

• Spare Parts Lists

• Accessories

• Dimensional Drawings

Please visit: https://servaid.atlascopco.com.

For further Technical Information, please contact your local Atlas Copco representative.

Safety Data Sheets MSDS/SDS

The Safety Data Sheets describe the chemical products sold by Atlas Copco.

Please consult the Atlas Copco website for more information www.atlascopco.com/sds.

Country of Origin

For the Country of Origin, please refer to the information on the product label.

Dimensional Drawings

Dimensional Drawings can be found either in the Dimensional Drawings Archive, or on ServAid.

Please visit: http://webbox.atlascopco.com/webbox/dimdrw or https://servaid.atlascopco.com.

Overview

• Battery Overview
• Ambient Temperature
• Battery Charger Data

Battery Overview

Position	Description
1	Release button
2	State of charge indicator

Ambient Temperature

For best battery performance and life time, keep battery within temperature intervals.

Do not place battery in direct sunlight.

Battery Charger Data

Other chargers not allowed. Charging the battery on a not approved charger is considered as altering the system and will make the tool certification invalid.

Installation

• Installation Instructions
  • Attaching and Removing the Battery

Installation Instructions

• Attaching and Removing the Battery

Attaching and Removing the Battery

Operation

• General Operation Safety
• Starting the Battery
• Battery Charge and Health Display

General Operation Safety

Read these safety instructions before use.

Operation

• Check the battery pack for damage before every use. Do not use damaged devices.

• The battery voltage must match the voltage mentioned on the type plate of the charger and tool.

• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

• Do not incinerate, disassemble or crush the battery pack.

• Avoid contact with fluids oozing out of defective battery packs. Rinse with water in case of accidental contact with fluid. Consult a doctor if fluid comes into contact with eyes.

Charging

• Other chargers than the one stated under Battery Charger Data are not allowed. Charging the battery on a not approved charger is considered as altering the system and will make the tool certification invalid.

• Insert only clean and dry battery packs into the battery holder of the charger.

• If a protective cover is used on the battery, make sure the cover is removed and look for potential damage before charging.

• Check for damage on the battery before charging. Do not charge any battery pack that has been damaged during use or by accident (e.g. dents on the housing or any other damages). Replace damaged battery packs.

• Always remove fully charged batteries from the charger. Do not let the fully charged battery remain on the charger.

• Do not operate the charger close to an explosive environment, for example close to a gas filling station.

• We recommend users to operate the charger in a defined protected and secure area (e.g. in charging cabinets or under supervision).

• Make sure the charger is stable when charging, to ensure that the batteries do not fall to the floor.

If you identify noise or extensive heat from a battery:

Storage

• Do not store the battery packs along with metal objects. No metal parts should come in contact with battery connectors; risk of short circuit.

• Store batteries and chargers in a dry place, and keep dry at all times.

• Avoid storing batteries fully charged.

• Do not store your battery connected to the power tool for longer periods

• Maintenance charge batteries in storage, preferably every 12 months.

Disposal

• Do not dispose of battery packs by throwing them into fire or through household waste.

Starting the Battery

Press the button to start the battery.

Battery Charge and Health Display

Indication	Flash pattern	Battery status	Battery state of charge	Remark
	Steady light	Full charge	> 75 %
	Steady light	Medium charge	55 - 74 %
	Steady light	Low charge	21 - 54 %	Charge battery when possible
	Flashing	Empty	< 21 %	Charge battery
	Steady light for 1.5 second	Self-test when powering on		Battery operational after 1.5 second
	Steady light	Battery cell temperature out of range: Too high temperature		Let battery cool before continuing operation
		Battery cell temperature out of range: Too low temperature		Make sure ambient temperature is within range. See Battery Temperatures.
		Too high discharge current to tool		Check the tool configuration. Remove battery from tool
		Too high charge current		Remove battery from charger and replace charger
		Invalid charger		Use appropriate charger. See Battery Charger Data.
		Too high voltage applied externally to battery connector
	Steady light	Unrecoverable error		Replace battery

When attaching the battery to the charger, the charging procedure will start and go on for 20 seconds. The charging is then temporarily stopped as the battery performs a self-test. The self-test continues for 10 seconds and after this the battery resumes charging again.

State of Health (SOH) Indicators:

SOH indicates how much of the original design capacity that is left in the battery cells, that is, how much the battery has degraded since it was new.

SOH is not an indication of current battery charge.

When the button is pressed for 10 seconds the battery SOH is shown, as listed below:

Indication	Flash pattern	State of Health (SOH)
	1 flash, green	More than 80% of the original capacity
	1 flash, yellow	Between 70-80% of the original capacity
	1 flash, red	Less than 70% of original capacity

State of Health Signals

When the button is pressed for 20 seconds the battery state is shown by the LEDs flashing in sequence, as listed below.

If the button is pressed for more than one minute, the battery goes into boot mode. All three white indicators will flash one by one, in sequence.

Recycling

• Environmental Regulations

Environmental Regulations

When a product has served its purpose it has to be recycled properly.

Batteries shall be taken care of by your national battery recovery organization.