Product Information

• General Information
  • Safety Signal Words
  • Website
  • ServAid
  • Safety Data Sheets MSDS/SDS
  • Country of Origin
  • Dimensional Drawings
  • Warranty
• Overview
  • Intended Use
  • Residual risks
  • Technical Product Data
• Service Overview
  • Service Recommendations

General Information

WARNING

Risk of Property Damage or Severe Injury

Ensure that you read, understand and follow all instructions before operating the tool. Failure to follow all the instructions may result in electric shock, fire, property damage and/or severe bodily injury.

• Read all Safety Information delivered together with the different parts of the system.

• Read all Product Instructions for installation, operation and maintenance of the different parts of the system.

• Read all locally legislated safety regulations regarding the system and parts thereof.

• Save all Safety Information and instructions for future reference.

Safety Signal Words

Website

Information concerning our Products, Accessories, Spare Parts and Published Matters can be found on the Atlas Copco website.

Please visit: www.atlascopco.com.

ServAid

ServAid is a portal that is continuously updated and contains Technical Information, such as:

• Regulatory and Safety Information

• Technical Data

• Installation, Operation and Service Instructions

• Spare Parts Lists

• Accessories

• Dimensional Drawings

Please visit: https://servaid.atlascopco.com.

For further Technical Information, please contact your local Atlas Copco representative.

Safety Data Sheets MSDS/SDS

The Safety Data Sheets describe the chemical products sold by Atlas Copco.

Please consult the Atlas Copco website for more information www.atlascopco.com/sds.

Country of Origin

For the Country of Origin, please refer to the information on the product label.

Dimensional Drawings

Dimensional Drawings can be found either in the Dimensional Drawings Archive, or on ServAid.

Please visit: http://webbox.atlascopco.com/webbox/dimdrw or https://servaid.atlascopco.com.

Warranty

• Product warranty will expire 12+1 months after dispatch from Atlas Copco's Distribution Center.

• Normal wear and tear on parts is not included within the warranty.

  • Normal wear and tear is that which requires a part change or other adjustment/overhaul during standard tools maintenance typical for that period (expressed in time, operation hours or otherwise).

• The product warranty relies on the correct use, maintenance, and repair of the tool and its component parts.

• Damage to parts that occurs as a result of inadequate maintenance or performed by parties other than Atlas Copco or their Certified Service Partners during the warranty period is not covered by the warranty.

• To avoid damage or destruction of tool parts, service the tool according to the recommended maintenance schedules and follow the correct instructions.

• Warranty repairs are only performed in Atlas Copco workshops or by Certified Service Partners.

Atlas Copco offers extended warranty and state of the art preventive maintenance through its ToolCover contracts. For further information contact your local Service representative.

For electrical motors:

• Warranty will only apply when the electric motor has not been opened.

Overview

• Intended Use
• Residual risks
• Technical Product Data

Intended Use

This device is exclusively intended for professional use as a drive mechanism for hydraulic torque tools in line with the description given in these product information.

• Any other use is considered to be improper

• In particular , the use of the machine as a drive for all other pump units such as presses, hoisting cylinders, hydraulic shears, spreaders, etc. is improper use.

• Improper use of the device or modifications to the device undertaken by the end-user exclude any liability on the part of the manufacturer and invalidate the declaration of conformity.

• In this case the user is liable for damages resulting from the use of the device.

Residual risks

WARNING

The surface of the oil cooler (if fitted) becomes hot; keep a safe distance.

Danger due to noise: maximum noise level 82 dB(A); the end-user must make personal protective equipment (ear-protectors) available.

Technical Product Data

Technical Product Data can be found on either ServAid, or the Atlas Copco website.

Please visit: https://servaid.atlascopco.com or www.atlascopco.com.

Service Overview

• Service Recommendations

Service Recommendations

Preventive maintenance is recommended at regular intervals. See the detailed information on preventive maintenance. If the product is not working properly, take it out of service and inspect it.

If no detailed information about preventive maintenance is included, follow these general guidelines:

• Clean appropriate parts accurately

• Replace any defective or worn parts

Installation

• Installation Instructions
  • Use and Conditions for Storage
• Initial Configuration
  • Before Initial Operation

Installation Instructions

• Use and Conditions for Storage

Use and Conditions for Storage

• Ambient temperature: -10 to +40°C for use and storage.

• Protect from rain during use and storage.

• Contact Atlas Copco in the event of change in working conditions or use of this product.

• Power supply connections: In the event of modification to the mains connection, protection against shock must be guaranteed by installing a protective earth system.(delivery with earthed pin plug).

Initial Configuration

• Before Initial Operation

Before Initial Operation

• Carry out a visual inspection before each start-up.

• Check remote control, mains plug and all cables for damage.

• Check hose couplings, hoses and hydraulic torque tools for damage.

Hoses and hydraulic torque tools are not included in delivery.

• Hose couplings, hoses and hydraulic torque tools must be designed for an operating pressure of Max.700 bar / 10,000 PSI..

• Hose couplings, hoses and hydraulic torque tools with lower operating pressures are not permitted to be connected to the pump unit.

• Check the entire machine, fluid reservoir, motor, manometer and air line lubricator for damage such as ruptures or leaks.

• Have damaged parts replaced by qualified technicians before operation.

• Check hose couplings for dirt.

• Clean soiled hose couplings before operation.

• Check the fluid level; the level must be up to the middle of the oil sight glass; top up hydraulic fluid, if needed. Use recommended grade of oil as per chart see also,Hydraulic Fluid

• Set up the pump unit on a level, horizontal surface so that it is prevented from falling over or falling down.

• Connect the pump unit by means of the threaded couplings with the hoses and with the hydraulic torque tool.

  

  Refer below picture to check section,

  

• Connect the pump unit to the air supply.

• Ensure a dynamic pressure of 5-6 bar and air volume of minimum 40 cfm is available. Higher pressures can lead to excessive wear and tear or damage the seals / valves.

The pump unit must not be operated without the hoses and the hydraulic torque tool connected up.

Operation

• Ergonomic Guidelines
• Operating Instructions
  • Operating the Machine
  • Pressure and / or Torque Adjustment
  • Tightening or loosening threaded connections
  • Operating Hydraulic Pump
  • Shut down procedure

Ergonomic Guidelines

Consider your workstation as you read through this list of general ergonomic guidelines to identify areas for improvement in posture, component placement, or work environment.

• Take frequent breaks and change work positions frequently.

• Adapt the workstation area to your needs and the work task.

  • Adjust for a convenient reach range by determining where parts and tools need to be located to avoid static load.

  • Use workstation equipment such as tables and chairs appropriate for the work task.

• Avoid work positions above shoulder level or with static holding during assembly operations.

  • When working above shoulder level, reduce the load on the static muscles by lowering the weight of the tool, using for example torque arms, hose reels or weight balancers. You can also reduce the load on the static muscles by holding the tool close to the body.

  • Take frequent breaks.

  • Avoid extreme arm or wrist postures, particularly during operations requiring a degree of force.

• Adjust for a convenient field of vision that requires minimal eye and head movements.

• Use appropriate lighting for the work task.

• Select the appropriate tool for the work task.

• In noisy environments, use ear protection equipment.

• Use high-quality inserted tools and consumables to minimize exposure to excessive levels of vibration.

Operating Instructions

• Operating the Machine
• Pressure and / or Torque Adjustment
• Tightening or loosening threaded connections
• Operating Hydraulic Pump
• Shut down procedure

Operating the Machine

Pressure and / or Torque Adjustment

The torque of hydraulic torque wrenches is proportional to the pressure. This is why before tightening or loosening bolted connections the maximum pressure of the machine and thus the maximum torque of the torque tool must be adjusted.

Please check torque pressure chart of each tool carefully for setting the pressure. Different size tools will deliver different torque at same pressure.

Tightening or loosening threaded connections

Please check manual of hydraulic torque wrenches for bolt tightening and loosening operation.

Operating Hydraulic Pump

Setting Working Pressure on the Pump

To set the pressure on the pump, follow this procedure:

Applying Torque to Wrench

Having set your target pressure, cycle the tool three or four times to full pressure. Cycling the tool ensures that the system is operating properly and removes trapped air, if any.

Verify that any impact sockets used are rated to accept the full torque output of the tool they are to be used with. Ensure the correct size impact socket for the nut A/F has been selected, placed on the square drive and secure with a locking pin and ring.

Place the tool and the socket on the nut, making sure that the socket has fully engaged the nut, check that the drive retainer is engaged.

Make sure the reaction arm is firmly abutted against a stationary object (i.e. an adjacent nut, flange, equipment housing etc.). When positioning the wrench, make sure that the hose connections are well clear of any obstructions and that all body parts are safely out of harm's way. Then apply momentary pressure to the system to ensure proper tool placement. If it doesn't look or act right, stop and re-adjust the reaction arm.

Read Safety Instructions supplied with the torque wrench for further guidance on tool usage

The reading of full preset pressure after the cylinder is extended DOES NOT INDICATE that this pressure (torque) is applied to the bolt. It only indicates that the cylinder is fully extended and cannot turn the socket or the ratchet link further until the tool automatically resets itself.

Releasing the remote control button will retract the cylinder. The tool will automatically reset itself and the operator will hear an audible "click" indicating he can again push the remote control button and the socket will turn. Each time the cylinder is extended and retracted, it is called a cycle. Successive cycles are made until the tool "stalls" at the pre-set Torque/PSI with an accuracy of +/-3%. Repeatability is +/- 1%.

Always attempt one final cycle to ensure the "stall" point has been reached.

Should the tool "lock-on" after the final cycle, push down on the remote control button once more (to build pressure) and, while maintaining this pressure, pull back on the external disengagement lever (RT) or reaction Pawl (RTX). Releasing the remote control while continuing to hold back on the pawl lever/reaction pawl will allow the tool to be removed easily.

Loosening Procedures

First, set the pump to 9,000 PSI (Do not try directly at 10.000 PSI). Change the drive and the reaction arm to the loosening mode (Left = Loose), assuring the reaction arm abuts squarely off a solid reaction point. Press and hold the remote control button down. Pressure will decrease as the socket begins to turn. As the cylinder extends fully, you will hear an audible "click". Release the remote control button, and the cylinder automatically retracts, at this time you will again hear the audible "click". Repeat this process until the fastener can be removed by hand. First, set the pump to 9,000 PSI (Do not try directly at 10.000 PSI). Change the drive and the reaction arm to the loosening mode (Left = Loose), assuring the reaction arm abuts squarely off a solid reaction point. Press and hold the remote control button down. Pressure will decrease as the socket begins to turn. As the cylinder extends fully, you will hear an audible "click". Release the remote control button, and the cylinder automatically retracts, at this time you will again hear the audible "click". Repeat this process until the fastener can be removed by hand.

NOTE : If the bolt does not loosen with the above procedure, it is an indication that you need a larger tool to loosen the bolt.

Setting Torque

All Atlas Copco power packs operate at a pressure range from 500 to 10,000 PSI and are fully adjustable. They have been engineered and designed for portability and high flow for increased speed. Before using your Atlas Copco power pack, check the following points.

• Is the reservoir filled with oil?

• Where is the closest electrical outlet at the job site?

• Is there enough air pressure (60 to 100 PSI) and Air flow at the job site? (Air units only)

• Is the gauge mounted and rated for 10,000 PSI/700 bar?

Working Pressure

The pump's maximum working pressure is 10,000 PSI / 700bar. Make sure all hydraulic equipment and accessories are rated for 10,000 PSI / 700bar operating pressure. Hydraulic pumps are available with higher pressure outputs, if not using an Atlas Copco power pack verify maximum operating pressure of the unit being used and ensure the system maximum operating pressure (10,000 PSI / 700 bar) is not exceeded.

Hydraulic Connections

Never disconnect or connect hydraulic hoses or fittings without first unloading the wrench. Unplug the electrical cord of the pump, and open all hydraulic controls several times to assure that the system has been depressurized. If the system includes a gauge, double check the gauge to assure pressure has been released. When making a connection with quick disconnect couplings, make sure the couplings are fully engaged threaded connections such a fittings, gauges etc. must be clean and securely tightened and leak free.

CAUTION - Loose or improperly threaded couplers can be potentially dangerous if pressurized, however, severe over tightening can cause premature thread failure. Fittings need to be only tightened secure and leak free. Never grab, touch or in any way come in contact with a hydraulic pressure leak. Escaping oil can penetrate the skin and cause injury. Do not subject the hose and potential hazard such as sharp surfaces, extreme heat or heavy impact. Do not allow the hose to kink and twist. Inspect the hose for wear before it is used.

Electrical Power

Prior to Use

Check hydraulic oil (Use Atlas Copco maximiser range Grade 46) level to prevent possible pump burnout. Open the filler plug located on the reservoir plate. Look at oil fill level on the oil sight gauge. The oil level should be approximately 2" from the top of the reservoir plate- with motor off. Add oil as necessary. Do not mix different grades of oil. Make sure all desired gauge, valve, hose and quick coupler connections are tight and secure before operating. The use of a pressure gauge is required for normal pump operation. Mounted on the manifold, the gauge permits the operator to monitor the load on the wrench. Class1 certified calibrated gauges are available for most applications

Shut down procedure

Never use spanner or any external tool to open the hydraulic connections. Ensure all pressure is released by pressing the solenoid valve again if couplings hard to open. Shake the hoses near the couplers while keep trying to unscrew the connections.

Service

• General Service Instructions
• Maintenance Instructions
  • Oil change intervals
  • Oil specification
  • Factory Connections for Couplers and Nipples
  • Transportation Instructions
  • Service Recommendations
• Lubrication Instructions
  • Hydraulic Fluid

General Service Instructions

• Electrical work may only be carried out by qualified electricians.

• Use only original spare parts as per the spare parts list.

• Hydraulic fluid change and filter change (if fitted) at least once every year or at the latest after every 300 operation hours; if necessary earlier, if the pump unit is used in a dusty environment.

  • Recommended hydraulic fluids: check oil chart.

  • Hydraulic fluid quantity : see Technical Data

  • Fluid filter as per spare parts list.

• Quick-Disconnects

  • Fittings should be checked periodically for leaks. Dirt or foreign materials should be kept away from fittings.

  • Clean before use.

• Hydraulic Gauge

  • Some gauges are liquid filled. Should this liquid level drop, it indicates external leakage, and replacement is necessary.

  • Should the gauge fill with hydraulic oil, it indicates internal failure and it should be discarded.

• Filter on Pump

  • The filter should be replaced twice a year in normal use and more often if the pump is used daily or in a dirty, harsh environment.

• Remote Control

  • The air line to the remote control unit should be checked for obstructions or kinks in the line periodically. If there is a bend or break in the line, it must be replaced. The spring-loaded buttons on the remote handle should be checked in the event of operating difficulties.

Maintenance Instructions

• Oil change intervals
• Oil specification
• Factory Connections for Couplers and Nipples
• Transportation Instructions
• Service Recommendations

Oil change intervals

Portable hydraulic equipment are susceptible to contamination due to the extreme conditions in which they work. Although selected fluids are designed to suffer less degradation than another product, we recommend an oil change and filter at least every 750 hours of use, or once a year, whichever occurs first.

It is recommended to periodically check the color of the oil and level seeking extreme contamination or loss of oil level that will require to refill the tank.

For oil changes or refilling, it is always recommended to use the same oil in the pump.

In case of an emergency and having to refill the tank and mix different types of fluids, it is preferred to use fluids with no additives as the HL or HLP fluids. After that, and always before a period of 2-4 working days, replace the oil with recommended oils.

Oil specification

The behavior “In-service” of a hydraulic equipment heavily depends on the quality and characteristics of the hydraulic fluid selected. The choice of the specification and viscosity of the hydraulic fluid should be based of the conditions of use, taking into account several factors as follows:

• The range of environmental temperature.

• The range of oil viscosity defined for the equipment.

• The application (for example: range of pressures, sources of contamination of the hydraulic fluid, the type of pump).

• The ease of getting a proper replacement or equivalent hydraulic liquid.

Factory Connections for Couplers and Nipples

Tool

• Advance Side - Male

• Retract Side - Female

Hose

• Advance Side - Female to Female

• Retract Side - Male to Male

Pump

• Advance Side - Male

• Retract Side - Female

Transportation Instructions

Use corrugated cardboard for packing.

Use pallet to lift pump and secure with strapping properly.

Pump should be transported without oil.

Transport of the machine ready for operation:

• Please follow local guidelines for weight handling by hand.

• With industrial trucks: Use suitable hoisting equipment

• Hanging: Use suitable slings (no chains, no metal ropes).

  

Service Recommendations

Preventive maintenance is recommended at regular intervals. See the detailed information on preventive maintenance. If the product is not working properly, take it out of service and inspect it.

If no detailed information about preventive maintenance is included, follow these general guidelines:

• Clean appropriate parts accurately

• Replace any defective or worn parts

Lubrication Instructions

• Hydraulic Fluid

Hydraulic Fluid

The performance of hydraulic equipment is heavily dependent on the quality and characteristics of the hydraulic fluid selected for use. The choice of the specification and viscosity of the hydraulic fluid should be based of the conditions of use, taking into account several factors as follows:

• The range of environmental temperature.

• The range of oil viscosity defined for the equipment.

• The application (range of pressures, sources of contamination of the hydraulic fluid, the type of pump, etc.)

• The ease of getting a proper replacement or equivalent hydraulic fluid.

  Example: ISO Grade 15, 32 and 68.

  For changing or refilling the oil, it is recommended to use the same oil as supplied with the pump.

Hydraulic Oil Selection Chart

Please use the link below to find our safe data sheets for Maximizer.

https://www.atlascopco.com/en-uk/sys/safetydatasheets

Troubleshooting

• Troubleshooting Guide

Troubleshooting Guide

Recycling

• Environmental Regulations

Environmental Regulations

When a product has served its purpose it has to be recycled properly. Dismantle the product and recycle the components in accordance with local legislation.