Product Information

• General Information
  • Safety Signal Words
  • Warranty
  • Website
  • ServAid
  • Safety Data Sheets MSDS/SDS
  • Special Precaution
    • PTFE
  • Country of Origin
  • Dimensional Drawings
• Overview
  • Technical Product Data

General Information

WARNING

Risk of Property Damage or Severe Injury

Ensure that you read, understand and follow all instructions before operating the tool. Failure to follow all the instructions may result in electric shock, fire, property damage and/or severe bodily injury.

• Read all Safety Information delivered together with the different parts of the system.

• Read all Product Instructions for installation, operation and maintenance of the different parts of the system.

• Read all locally legislated safety regulations regarding the system and parts thereof.

• Save all Safety Information and instructions for future reference.

Safety Signal Words

Warranty

• Product warranty will expire in 12+1 months after dispatch from Atlas Copco's Distribution Center.

• Normal wear and tear on parts is not included within the warranty.

  • Normal wear and tear is that which requires a part change or other adjustment/overhaul during standard tool maintenance typical for that period (expressed in time, operation hours or otherwise).

• The product warranty relies on the correct use, maintenance, and repair of the tool and its component parts.

• Damage to parts that occurs as a result of inadequate maintenance or performed by parties other than Atlas Copco or their Certified Service Partners during the warranty period is not covered by the warranty.

• To avoid damage or destruction of tool parts, service the tool according to the recommended maintenance schedules and follow the correct instructions.

• Warranty repairs are performed only in Atlas Copco workshops or by Certified Service Partners.

Atlas Copco offers extended warranty and state-of-the-art preventive maintenance through its ToolCover contracts. For further information, contact your local Service representative.

For electrical motors:

• Warranty will apply, only when the electric motor has not been opened.

Website

Information concerning our Products, Accessories, Spare Parts and Published Matters can be found on the Atlas Copco website.

Please visit: www.atlascopco.com.

ServAid

ServAid is a portal that is continuously updated and contains Technical Information, such as:

• Regulatory and Safety Information

• Technical Data

• Installation, Operation and Service Instructions

• Spare Parts Lists

• Accessories

• Dimensional Drawings

Please visit: https://servaid.atlascopco.com.

For further Technical Information, please contact your local Atlas Copco representative.

Safety Data Sheets MSDS/SDS

The Safety Data Sheets describe the chemical products sold by Atlas Copco.

Please consult the Atlas Copco website for more information www.atlascopco.com/sds.

Special Precaution

• Check that the power socket is properly fastened.

• Replace the square drive retainer or socket if worn.

• Avoid unnecessary idling.

• When using a suspension yoke, make sure that it is in good condition and correctly fastened.

PTFE

WARNING

Polymer Hazard

The vanes in this product contain PTFE (a synthetic fluoropolymer). Due to wear, there might be PTFE particles inside the product. Heated PTFE can produce fumes which may cause polymer fume fever with flu-like symptoms, especially when smoking contaminated tobacco.

Health and Safety recommendations for PTFE must be followed when handling vanes and other components:

• Do not smoke when servicing this product

• PTFE-particles must not come in contact with open fire, glow or heat

• Motor components must be washed with cleaning fluid and not blown clear with an air line

• Wash your hands before starting any other activity

Country of Origin

For the Country of Origin, please refer to the information on the product label.

Dimensional Drawings

Dimensional Drawings can be found either in the Dimensional Drawings Archive, or on ServAid.

Please visit: https://webbox.atlascopco.com/webbox/dimdrw or https://servaid.atlascopco.com.

Overview

• Technical Product Data

Technical Product Data

Technical Product Data can be found on either ServAid, or the Atlas Copco website.

Please visit: https://servaid.atlascopco.com or www.atlascopco.com.

Installation

• Installation Requirements
  • Air Quality
  • Air Lubrication Guide
  • Compressed Air Connection
  • Air Pressure Regulation
• Installation Instructions
  • Recommended hose sizes
  • Installation of Flexible Hose
  • Initial Setting of Torque

Installation Requirements

• Air Quality
• Air Lubrication Guide
• Compressed Air Connection
• Air Pressure Regulation

Air Quality

• For optimum performance and maximum product life we recommend the use of compressed air with a maximum dew point of +10°C (50°F). We also recommend to install an Atlas Copco refrigeration type air dryer.

• Use a separate air filter which removes solid particles larger than 30 microns and more than 90% of liquid water. Install the filter as close as possible to the product and prior to any other air preparation units to avoid pressure drop.

For impulse/impact tools make sure to use lubricators adjusted for these tools. Regular lubricators will add too much oil and therefore decrease the tool performance due to too much oil in the motor.

Make sure that the hose and couplings are clean and free from dust before connecting to the tool.

Both lubricated and lubrication free products will benefit from a small quantity of oil supplied from a lubricator.

Air Lubrication Guide

Recommended air lubricators:

• Atlas Copco Optimizer (1 liter) 9090 0000 04

• Q8 Chopin 46

• Q8 Chopin 32

• Shell Air Tool Oil S2 A 320

• Mobil SHC Cibus 32

Compressed Air Connection

WARNING

Risk of severe injury

Air under pressure can cause injury.

• Always shut off the air supply when not in use or before any adjustments.

• Drain the hose of air pressure and disconnect the tool from air supply when not in use or before any adjustments.

• Always use the correct hose size and air pressure for the tool.

WARNING

Compressed Air

High air pressure can cause severe damage and bodily injury.

• Do not exceed maximum air pressure.

• Make sure that there are no damaged or loose hoses or fittings.

For correct air pressure and hose size, see the Technical Product Data on - https://servaid.atlascopco.com or www.atlascopco.com.

Make sure that the hose and couplings are clean and free from dust before connecting to the tool.

Air Pressure Regulation

Make sure to adjust the regulator to the lowest expected pressure on the line.

Adjusting the air pressure will have the following consequences:

• Decreasing the air pressure will result in a slower but more accurate tool.

• Increasing the air pressure will result in a faster but less accurate tool.

If the pressure from the airline is below five bar, a tool from the EP L-series (designed for low pressure installations) is recommended.

Installation Instructions

• Recommended hose sizes
• Installation of Flexible Hose
• Initial Setting of Torque

Recommended hose sizes

Make sure that all connections, adapters and couplings exceed the recommended minimum inner diameter, corresponding to the recommended hose size of the tool. Refer to the examples in the table. Recommended hose size for a specific tool is found in "Technical specifications" in https://servaid.atlascopco.com

Installation of Flexible Hose

To prevent tool vibrations use a flexible hose for compressed air with a minimum length of 300 mm (12") between the tool and the quick coupling.

Initial Setting of Torque

To minimize the risk of damage to the actual joint we recommend to set the torque slightly lower on the test joint than the torque wanted for the application. Make sure to use the same equipment, such as for example extensions, sockets and air pressure on the test joint as will be used on the actual joint.

Make sure to always verify the torque settings on your actual joint.

Operation

• Ergonomic Guidelines
• Operating Instructions
  • Torque Check - Residual Torque Measurement on Actual Joint
  • Position of reversing knob
  • Optimizing the Tool Performance
  • Operating Instructions

Ergonomic Guidelines

Consider your workstation as you read through this list of general ergonomic guidelines and see if you can identify areas for improvement in posture, component placement, or work environment.

• Take frequent breaks and change work positions frequently.

• Adapt the work area to your needs and the work task.

  • Adjust for convenient reach range by determining where parts or tools should be located to avoid static load.

  • Use workstation equipment such as tables and chairs appropriate for the work task.

• Avoid work positions above shoulder level or with static holding during assembly operations.

  • When working above shoulder level, reduce the load on the static muscles by reducing the weight of the load. You can also reduce the load on the static muscles by holding the load close to the body.

  • Make sure to take frequent breaks.

  • Avoid extreme arm or wrist postures, particularly for operations requiring a degree of force.

• Adjust for convenient field of vision by minimizing movement of the eyes and head during the work task.

• Use the appropriate lighting for the work task.

• Use ear protection equipment in noisy environments.

• Use dust extraction system or mouth protection mask in dusty environments.

Operating Instructions

• Torque Check - Residual Torque Measurement on Actual Joint
• Position of reversing knob
• Optimizing the Tool Performance
• Operating Instructions

Torque Check - Residual Torque Measurement on Actual Joint

* Torque required to cause the threads of the fastener (including its head) on which torque is applied, to move relative to the mating thread.

Position of reversing knob

Optimizing the Tool Performance

It is not recommended to use extensions with pulse tools. Extensions cause vibrations, which in turn may cause wear on the tool, longer tightening time, limited accuracy and difficulty reaching maximum torque. If an extension is necessary due to accessibility constraints, it should be as short as possible. Guided sockets or extensions are strongly recommended.

Recommended number of pulses

The pulse tool shall reach the target torque, with shut off, within 5-20 pulses. Measure the number of pulses to reach the target torque with an analyzer. The tightening time can also be used as a guide, to know if the tool is set correctly:

• ≤ 1 second for tools up to 30 Nm

• ≈ 1 second for tools up to 80 Nm

• ≈ 2 seconds for tools up to 150 Nm

• ≈ 5 seconds for tools up to 450 Nm

• ≤ 10 seconds for tools up to 850 Nm

If the target torque is reached within less than 5 pulses (= short tightening time), the torque scatter will increase and it can be difficult to adjust to the right level, especially on hard joints.

If the target torque is reached after more than 20 pulses (= too long tightening time) the wear will increase and more frequent oil filling and service will be required. Too long tightening time, in combination with high production rate, may also result in excessive heating of the oil. In that case the power will decrease with longer tightening time and sometimes no shut off.

If the target torque is reached within less than 5 pulses, adjust it by:

• Decreasing the air pressure.

• Reducing the speed with the AutoTrim or Trim valve.

• If the above is not possible or does not give the wanted results, a smaller tool may be a better choice.

If the target torque is reached with more than 20 pulses, adjust it by:

• Increasing the dynamic air pressure to 6-7 bar for standard EP tools, or up to 5 bar for low pressure EP L-tools.

• Adjusting the AutoTrim or Trim valve to give maximum power/speed.

• If the above is not possible or does not give the wanted results, a bigger tool may be a better choice.

When changing the air pressure, measure the target torque again and adjust it if needed.

Operating Instructions

Service

• Maintenance Instructions
  • Service tools
  • Preventive Maintenance
• Lubrication Instructions
  • Rust Protection and Cleaning
  • Lubrication Guide
  • To fill the pulse unit with oil
  • To refill the pulse unit
• Dismantling/Assembling Instructions
  • Tightening of Threaded Connections
• Torque Check - Residual Torque Measurement on Actual Joint

Maintenance Instructions

• Service tools
• Preventive Maintenance

Service tools

Atlas Copco Service tools are designed to make assembly and disassembly fast and easy with less risk of damaging parts in the process.

When assembling the tool after service it is important to tighten the parts correctly to:

• Optimize performance of the tool.

• Minimize the risk of parts coming loose during operation.

You can find information about service tools and tightening data in the Spare part list on ServAid.

Preventive Maintenance

Preventive maintenance is recommended once per year or after a maximum of 250.000 tightenings. A complete overhaul includes:

• Clean the following parts: pulse unit, air motor, silencer and strainer of the inlet adapter, trigger and reversing valve.

• Replace worn or damaged parts and filter.

Only replace the o-rings in the pulse unit at the complete overhaul.

Lubrication Instructions

• Rust Protection and Cleaning
• Lubrication Guide
• To fill the pulse unit with oil
• To refill the pulse unit

Rust Protection and Cleaning

Water in the compressed air can cause rust. To prevent rust we strongly recommend to install an air dryer.

Water and particles can cause sticking of vanes and valves. This can be prevented by installing an air filter close to the product to avoid pressure drop.

Before longer stand stills always protect your tool by adding a few drops of air motor oil into the air inlet. Run the tool for 5–10 seconds and absorb any excess oil at the air outlet in a cloth.

Lubrication Guide

To fill the pulse unit with oil

Due to a possible microleakage of oil from the pulse unit, it could be necessary to refill the unit between the regular overhaul intervals. The frequency of this procedure depends on the type of application, number of cycles, tightening time etc. An indication of not enough oil is a decreased tightening torque and an increased pulse frequency.

After disassembly of pulse unit, fill with oil according to operation No. 1-3 below. Run the machine in a vice for 10 seconds according to operation No. 5 below. Then continue according to operation No. 6-11. For best performance use Atlas Copco pulse unit oil Bio. The Oil Filling Kit is composed of Atlas Copco Pulse unit oil Bio 150 ml and a syringe (1 ml). Ordering No. : 4081 0121 90.

To refill the pulse unit

Keep the pulse unit at normal room temperature.

Before the refill: Let the bubbles in the oil fade away, at least 30 min. after last run. Check that there are no bubbles in the oil and that the pulse unit is completely full (100%) before reducing the oil volume according to operation No. 10.

Dismantling/Assembling Instructions

• Tightening of Threaded Connections

Tightening of Threaded Connections

The tightening torque indicated in the exploded views (see Spare parts section in https://servaid.atlascopco.com) will give the right clamping force and prevent parts from loosening. It is important not to exceed the clamping force, these parts must be able to open up without being damaged at service. After some time of operation and in special circumstances, depending on application and usage, the parts may however loosen somewhat. The tightening torque can then be increased by 10-20% and some type of low or medium thread locking fluid can be applied.

Torque Check - Residual Torque Measurement on Actual Joint

* Torque required to cause the threads of the fastener (including its head) on which torque is applied, to move relative to the mating thread.

Recycling

• Environmental Regulations

Environmental Regulations

When a product has served its purpose it has to be recycled properly. Dismantle the product and recycle the components in accordance with local legislation.

Batteries shall be taken care of by your national battery recovery organization.