Multi Charger

Charger

Product Information

General Information

WARNING

Risk of Property Damage or Severe Injury

Ensure that you read, understand and follow all instructions before operating the tool. Failure to follow all the instructions may result in electric shock, fire, property damage and/or severe bodily injury.

  • Read all Safety Information delivered together with the different parts of the system.

  • Read all Product Instructions for installation, operation and maintenance of the different parts of the system.

  • Read all locally legislated safety regulations regarding the system and parts thereof.

  • Save all Safety Information and instructions for future reference.

In this Section

Safety Signal Words

The safety signal words Danger, Warning, Caution, and Notice have the following meanings:

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE

NOTICE is used to address practices not related to personal injury.

Warranty

  • Product warranty will expire 12+1 months after dispatch from Atlas Copco's Distribution Center.

  • Normal wear and tear on parts is not included within the warranty.

    • Normal wear and tear is that which requires a part change or other adjustment/overhaul during standard tools maintenance typical for that period (expressed in time, operation hours or otherwise).

  • The product warranty relies on the correct use, maintenance, and repair of the tool and its component parts.

  • Damage to parts that occurs as a result of inadequate maintenance or performed by parties other than Atlas Copco or their Certified Service Partners during the warranty period is not covered by the warranty.

  • To avoid damage or destruction of tool parts, service the tool according to the recommended maintenance schedules and follow the correct instructions.

  • Warranty repairs are only performed in Atlas Copco workshops or by Certified Service Partners.

Atlas Copco offers extended warranty and state of the art preventive maintenance through its ToolCover contracts. For further information contact your local Service representative.

For electrical motors:

  • Warranty will only apply when the electric motor has not been opened.

Website

Information concerning our Products, Accessories, Spare Parts and Published Matters can be found on the Atlas Copco website.

Please visit: www.atlascopco.com.

ServAid

ServAid is a portal that is continuously updated and contains Technical Information, such as:

  • Regulatory and Safety Information

  • Technical Data

  • Installation, Operation and Service Instructions

  • Spare Parts Lists

  • Accessories

  • Dimensional Drawings

Please visit: https://servaid.atlascopco.com.

For further Technical Information, please contact your local Atlas Copco representative.

Safety Data Sheets MSDS/SDS

The Safety Data Sheets describe the chemical products sold by Atlas Copco.

Please consult the Atlas Copco website for more information www.atlascopco.com/sds.

Country of Origin

For the Country of Origin, please refer to the information on the product label.

Dimensional Drawings

Dimensional Drawings can be found either in the Dimensional Drawings Archive, or on ServAid.

Please visit: http://webbox.atlascopco.com/webbox/dimdrw or https://servaid.atlascopco.com.

Overview

Product Functionality

Position

Description

1

Battery Holder

2

Power Cable

3

LED Green

4

LED Red

LED

Status

Glowing LED

Blinking LED

Green

Charging battery

Battery pack full

Battery pack is being charged

Red

Error

Temperature too high/low

Connection problems, battery pack defective

Operation

Operating Instructions

Operating the Multi Charger

The mains voltage must match the voltage stated on the type plate of the charger.

  1. Connect the charger to the mains power.

    The charger conducts a self-test. Both the LEDs glow for one second. The charger then goes into the stand-by mode and both LEDs switch off.

  2. Slide the battery on the battery holder of the charger. Charging starts automatically and the green LED flashes. The charging time depends on the charge state and capacity of the battery.

    When the battery is fully charged, the green LED glows. The charger automatically switches to retention charging.

New batteries reach their full capacity after approximately five charging/discharging cycles. Recharge batteries if they have not been used for a long time. The performance of the battery reduces when temperature falls below –10°C. Storing a battery for a long time at temperatures above 40°C can reduce the capacity.

Sleep Mode

If a battery is completely drained, it will go into sleep mode.

Wake up the battery by doing the following:

  1. Insert the battery in the charger.

    The charger will automatically detect that the battery is in sleep mode. The red and green LEDs of the charger start to flash, indicating that wake-up mode is activated.

  2. When the charger stops flashing, remove and reattach the battery immediately.

    The charger will resume with the regular charging procedure.

Troubleshooting

Troubleshooting

Indication

Event

Remark

Red LED glows

The battery pack is too hot or too cold.

The charging process starts when the battery has reached the correct charging temperature (5°C to 45°C).

Red LED flashes

Battery pack has not been placed correctly on the battery holder.

Battery pack is defective.

Recycling

Environmental Regulations

When a product has served its purpose it has to be recycled properly. Dismantle the product and recycle the components in accordance with local legislation.

Batteries shall be taken care of by your national battery recovery organization.